6450128-1 TE Connectivity, 6450128-1 Datasheet - Page 7

• Manufacturer Part Number: 6450128-1
• Description: MBXL R/A HDR STR 1P+24S+1P
• Manufacturer: TE Connectivity

Specifications of 6450128-1

• Product Series: XL
• Connector Type: Header
• Mount Angle: Right Angle
• Termination Style: Solder
• Mating Type: Squeeze-to-Release
• Pcb Mount Retention: With
• Guides: With
• Voltage Rating (signal) (vac): 60
• Voltage Rating (power) (vdc): 200
• Termination Post Length (mm [in]): 3.43 [0.135]
• Sequencing: No
• Pcb Mount Retention Type: Retention Clip/Post
• Connector Configuration Orientation: Left-to-Right
• Centerline, Dc Module (mm [in]): 6.35 [0.250]
• Centerline, Matrix (mm [in]): 2.54 x 2.54 [.100 x .100]
• Contact Type: Pin
• Contact Material (power): High Conductivity Copper
• Contact Material (signal): Copper Alloy
• Contact Plating, Mating Area, Material: Gold (30)
• Connector Style: Plug
• Housing Material: High Temperature Thermoplastic
• Total Number Of Dc Power: 2
• Total Number Of Signal: 24
• Connector Contact Configuration (no. Of Pos./type): 1/DC Power, 24/Signal, 1/DC Power
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Application Use: Cable-to-Board

4.
4.1.
4.2.
4.3.
4.4.
Rev C
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 3. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to
confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan shall specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Specimen Selection
Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Test Groups 1 and 4 were carried over from the
qualification results of the MBXL Cable Plug program (see Qualification Test Report 501-597-1)
since the contact interface is identical to the vertical header. Test Group 2 shall consist of 15
vertical headers with soldertails mated to right angle receptacles with soldertails. Five of these
headers shall be fully loaded with power and signal contacts, 5 with power contacts only, and 5
with signal contacts only. Test Group 3 shall consist of 3 vertical headers with soldertails mated to
3 right angle receptacles with soldertails. Test Group 5 shall consist of 5 vertical headers with
soldertails mated to 5 right angle receptacles with soldertails. Test Group 6 shall consist of 5
vertical headers with soldertails. Test Group 7 shall consist of 8 vertical headers with press-fit,
Eye-of-the-Needle tails.
Test Sequence
Qualification inspection shall be verified by testing specimens as specified in Figure 4.
108-1973
7 of 7