AD7688BRMZ Analog Devices Inc, AD7688BRMZ Datasheet - Page 23

• Manufacturer Part Number: AD7688BRMZ
• Description: IC ADC DIFF 16BIT 500KSPS 10MSOP
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of AD7688BRMZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 16
• Sampling Rate (per Second): 500k
• Number Of Converters: 1
• Power Dissipation (max): 21.5mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-TFSOP (0.118", 3.00mm Width)
• Resolution (bits): 16bit
• Sampling Rate: 500kSPS
• Input Channel Type: Differential
• Supply Voltage Range - Analog: 4.5V To 5.5V
• Supply Current: 1nA
• Digital Ic Case Style: SOP
• Number Of Elements: 1
• Resolution: 16Bit
• Architecture: SAR
• Sample Rate: 500KSPS
• Input Polarity: Bipolar
• Input Type: Voltage
• Rated Input Volt: ±5V
• Differential Input: Yes
• Power Supply Requirement: Single
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.5V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 21.5mW
• Differential Linearity Error: ±1LSB
• Integral Nonlinearity Error: ±1.5LSB
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 10
• Package Type: MSOP
• Input Signal Type: Differential
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7688CB - BOARD EVALUATION FOR AD7688
• Lead Free Status / Rohs Status: Compliant

AD7688
APPLICATION HINTS
LAYOUT
The printed circuit board that houses the AD7688 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7688, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these
couple noise onto the die, unless a ground plane under the
AD7688 is used as a shield. Fast switching signals, such as CNV
or clocks, should never run near analog signal paths. Crossover
of digital and analog signals should be avoided
At least one ground plane should be used. It could be common
or split between the digital and analog sections. In the latter
case, the planes should be joined underneath the AD7688s.
The AD7688 voltage reference input REF has a dynamic input
Figure 46. Example of Layout of the AD7688 (Top Layer)
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, and ideally right up against, the REF
and GND pins and connecting it with wide, low impedance
traces.
Finally, the power supplies VDD and VIO of the AD7688
should be decoupled with ceramic capacitors (typically 100 nF)
placed close to the AD7688 and connected using short and wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of layout following these rules is shown in
Figure 46 and Figure 47.
EVALUATING THE AD7688’S PERFORMANCE
Other recommended layouts for the AD7688 are outlined
Figure 47. Example of Layout of the AD7688 (Bottom Layer)
in the documentation of the evaluation board for the AD7688
(EVAL-AD7688). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD3.
Rev. A | Page 23 of 28