AD7763BSVZ Analog Devices Inc, AD7763BSVZ Datasheet
AD7763BSVZ
Specifications of AD7763BSVZ
Available stocks
Related parts for AD7763BSVZ
AD7763BSVZ Summary of contents
Page 1
FEATURES 120 dB dynamic range at 78 kHz output data rate 109 dB dynamic range at 625 kHz output data rate 112 dB SNR at 78 kHz output data rate 107 dB SNR at 625 kHz output data rate 625 ...
Page 2
AD7763 TABLE OF CONTENTS Features .............................................................................................. 1 Applications ....................................................................................... 1 Functional Block Diagram .............................................................. 1 General Description ......................................................................... 1 Revision History ............................................................................... 2 Specifications ..................................................................................... 3 Timing Specifications ....................................................................... 5 Timing Diagrams .......................................................................... 6 Absolute Maximum Ratings ............................................................ 7 ESD ...
Page 3
SPECIFICATIONS 2 DD1 DD DRIVE DD2 using on-chip amplifier with components as shown in Table 10, unless otherwise noted. Table 2. Parameter DYNAMIC PERFORMANCE Decimate × 256 Dynamic Range 2 ...
Page 4
AD7763 Parameter REFERENCE INPUT V Input Voltage REF V Input DC Leakage Current REF V Input Capacitance REF POWER DISSIPATION Total Power Dissipation Standby Mode POWER REQUIREMENTS AV (Modulator Supply) DD1 AV (General Supply) DD2 AV (Differential Amplifier Supply) DD3 ...
Page 5
TIMING SPECIFICATIONS 2 DD1 DD DRIVE DD2 Table 3. Parameter Limit MIN MAX f 1 MCLK 40 f 500 ICLK × t ...
Page 6
AD7763 TIMING DIAGRAMS FSO ( SCO ( DRDY ( SDO (O) D23 D22 D21 D20 D19 D18 D17 D16 D15 D14 D13 D12 D11 ...
Page 7
ABSOLUTE MAXIMUM RATINGS T = 25°C, unless otherwise noted. A Table 4. Parameter Rating AV to GND −0 DD1 ( GND −0 DD2 DD3 DD4 DV ...
Page 8
AD7763 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS MCLKGND AGND2 AGND1 DECAPA REFGND AGND4 AGND2 AGND2 NOTES 1. THE PADDLE MUST BE CONNECTED DIRECTLY TO THE GROUND PLANE OF Table 5. Pin Function Descriptions Pin No. Mnemonic DD1 4, ...
Page 9
Pin No. Mnemonic 8 DECAPA 30 DECAPB 17 R BIAS 37 RESET 3 MCLK 2 MCLKGND 36 SYNC 38 DRDY 39, 40, 45 SH2 ADR2:0 49 SCP 50 SDL 51 FSI 52 SDI 54 SDO 55 SCO ...
Page 10
AD7763 TERMINOLOGY Signal-to-Noise Ratio (SNR) The ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the Nyquist fre- quency, excluding harmonics and dc. The value for SNR is expressed ...
Page 11
TYPICAL PERFORMANCE CHARACTERISTICS 2 DD1 DD DRIVE DD2 are generated from 65536 samples using a 7-term Blackman-Harris window. 0 –50 –100 –150 –200 –250 0 5000 10000 15000 20000 FREQUENCY ...
Page 12
AD7763 0 –50 –100 –150 –200 –250 0 50000 100000 150000 200000 FREQUENCY (Hz) Figure 12. Normal Mode FFT, 100 kHz, −0.5 dB Input Tone, 32× Decimation 0 –50 –100 –150 –200 –250 0 50000 100000 150000 200000 FREQUENCY (Hz) ...
Page 13
CODE Figure 18. Normal Mode, 24-Bit Histogram, 256× Decimation 0.0010 +85°C 0.0005 +25°C 0 –40°C –0.0005 –0.0010 0 4194304 8388608 12582912 24-BIT CODE Figure ...
Page 14
AD7763 THEORY OF OPERATION The AD7763 employs a Σ-Δ conversion technique to convert the analog input into an equivalent digital word. The modulator samples the input waveform and outputs an equivalent digital word to the digital filter at a rate ...
Page 15
AD7763 INTERFACE READING DATA USING THE SPI INTERFACE The timing diagram in Figure 2 shows how the AD7763 transmits its conversion results using the SPI-compatible serial interface. The data being read from the AD7763 is clocked out using the serial ...
Page 16
AD7763 The Share Pins SH[2:0] of all the devices sharing the serial bus must be programmed for the correct number of devices that are sharing the serial bus. A binary value of N − 1 should be applied to the ...
Page 17
FSO and SDI pins can be tied together and each device written to individually by setting the appropriate address bits in the serial 32-bit word. The exception to this is when all devices can be written to at the ...
Page 18
AD7763 2 READING DATA USING THE I S INTERFACE The AD7763 has the capability of operating using an I interface. The interface is functional only for the output of stereo data and does not apply to writing to control registers, ...
Page 19
CLOCKING THE AD7763 The AD7763 requires an external, low jitter clock source. This signal is applied to the MCLK pin, and the MCLKGND pin is used to sense the ground from the clock source. An internal clock signal (ICLK) is ...
Page 20
AD7763 DRIVING THE AD7763 The AD7763 has an on-chip differential amplifier that operates with a supply voltage (AV ) from 3. 5.25 V. For a 4.096 V DD3 reference, the supply voltage must achieve ...
Page 21
Sampling Switch SS1 and Sampling Switch SS3 are driven by ICLK, whereas Sampling Switch SS2 and Sampling Switch SS4 are driven by ICLK . When ICLK is high, the analog input voltage is connected to CS1. On the falling edge ...
Page 22
AD7763 DECOUPLING AND LAYOUT RECOMMENDATIONS Due to the high performance nature of the AD7763, correct decoupling and layout techniques are required to obtain the performance as stated within this data sheet. Figure 35 shows a simplified connection diagram for the ...
Page 23
SUPPLY DECOUPLING Every supply pin must be connected to the appropriate supply via a ferrite bead and decoupled to the correct ground pin with a 100 nF, 0603 case size, X7R dielectric capacitor. There are two exceptions • Pin 12 ...
Page 24
AD7763 PROGRAMMABLE FIR FILTER As discussed in the Theory of Operation section, the third FIR filter on the AD7763 can be programmed by the user. The default coefficients that are loaded on reset are shown in Table 12. This gives ...
Page 25
DOWNLOADING A USER-DEFINED FILTER As discussed in the Programmable FIR Filter section, each of the filter coefficients is 27 bits in length: one sign bit and 26 magni- tude bits. To download coefficients for a user-specific FIR filter, a 32-bit ...
Page 26
AD7763 EXAMPLE FILTER DOWNLOAD The following is an example of downloading a short, user-defined filter with 24 taps. The frequency response is shown in Figure 38 –10 –20 –30 –40 –50 –60 –70 –80 0 100 200 300 ...
Page 27
REGISTERS The AD7763 has a number of user-programmable registers. The control registers are used to set the decimation rate, the filter configuration, the low power option, and the control of the differential amplifier. There are also digital gain, offset, and ...
Page 28
AD7763 STATUS REGISTER (READ ONLY) MSB PART 1 PART 0 DIE 2 DIE 1 DIE 0 Table 19. Bit Mnemonic Comment 15,14 PART[1:0] Part Number. These bits are constant for the AD7763 DIE[2:0] Die Number. These bits ...
Page 29
... SEATING 0.05 0.08 MAX PLANE COPLANARITY VIEW A ROTATED 90 ° CCW ORDERING GUIDE Model Temperature Range 1 AD7763BSVZ −40°C to +85°C AD7763BSVZ-REEL 1 −40°C to +85°C 1 EVAL-AD7763EDZ RoHS Compliant Part. 12.20 12.00 SQ 11. PIN 1 10.20 10.00 SQ TOP VIEW 9 ...
Page 30
AD7763 NOTES Rev Page ...
Page 31
NOTES Rev Page AD7763 ...
Page 32
AD7763 NOTES © 2005–2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05476-0-11/09(A) Rev Page ...