AD9262BCPZ-5 Analog Devices Inc, AD9262BCPZ-5 Datasheet - Page 18
![IC ADC 16BIT 5MHZ 64LFCSP](/photos/18/99/189913/4243362_sml.jpg)
AD9262BCPZ-5
Manufacturer Part Number
AD9262BCPZ-5
Description
IC ADC 16BIT 5MHZ 64LFCSP
Manufacturer
Analog Devices Inc
Datasheet
1.AD9262BCPZRL7.pdf
(32 pages)
Specifications of AD9262BCPZ-5
Data Interface
Serial, SPI™
Design Resources
Interfacing ADL5382 to AD9262 as an RF-to-Bits Solution (CN0062)
Number Of Bits
16
Sampling Rate (per Second)
160M
Number Of Converters
2
Power Dissipation (max)
703mW
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Resolution (bits)
16bit
Sampling Rate
160MSPS
Input Channel Type
Differential, Single Ended
Supply Voltage Range - Analog
1.7V To 1.9V
Supply Current
146mA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9262
External Reference Operation
If an external reference is desired, the internal reference can be
disabled by setting Serial Register 0x18[6] high. Figure 49 shows
an application using the
CLOCK INPUT CONSIDERATIONS
The AD9262 offers two modes of sourcing the ADC sample
clock (CLK+ and CLK−). The first mode uses an on-chip clock
multiplier that accepts a reference clock operating at the lower
input frequency. The on-chip phase-locked loop (PLL) then
multiplies the reference clock to a higher frequency, which is
then used to generate all the internal clocks required by the ADC
The clock multiplier provides a high quality clock that meets
the performance requirements of most applications. Using the
on-chip clock multiplier removes the burden of generating and
distributing the high speed clock.
The second mode bypasses the clock multiplier circuitry and
allows the clock to be directly sourced. This mode enables the
user to source a very high quality clock directly to the Σ-Δ
modulator. Sourcing the ADC clock directly may be necessary
in demanding applications that require the lowest possible ADC
output noise. See Figure 28, which shows the degradation in
SNR performance for the various PLL settings.
In either case, when using the on-chip clock multiplier or sourcing
the high speed clock directly, it is necessary that the clock
source have low jitter to maximize the ADC noise performance.
High speed, high resolution ADCs are sensitive to the quality of
the clock input. As jitter increases, the SNR performance of the
AD9262 degrades from that specified in Table 2. The jitter
inherent in the part due to the PLL root sum squares with any
external clock jitter, thereby degrading performance. To prevent
jitter from dominating the performance of the AD9262, the input
clock source should be no greater than 1 ps rms of jitter.
The CLK± inputs are self-biased to 450 mV (see Figure 31);
if the inputs are dc-coupled, it is important to maintain the
specified 450 mV input common-mode voltage. Each input pin
can safely swing from 200 mV p-p to 1 V p-p single-ended
about the 450 mV common-mode voltage. The recommended
clock inputs are CMOS or LVPECL.
The specified clock rate of the Σ-Δ modulator, f
The clock rate possesses a direct relationship to the available
input bandwidth of the ADC.
In either case, using the on-chip clock multiplier to generate the
Σ-Δ modulator clock rate or directly sourcing the clock, any
deviation from 640 MHz results in a change in input band-
Bandwidth = f
AVDD
0.1µF
Figure 49. External Reference Configuration
MOD
ADR130B
÷ 64
ADR130B
10µF
as a stable external reference.
0.5V
10kΩ
TO CURRENT
GENERATOR
MOD
, is 640 MHz.
Rev. A | Page 18 of 32
width. The input range of the clock is limited to 640 MHz ± 5%.
In situations where the AD9262 loses its clock and then later
regains it, it is important that the sample rate converter be reset
and reprogrammed before the desired output data rate is
achieved.
Direct Clocking
The default configuration of the AD9262 is for direct clocking
where the PLL is bypassed. Figure 50 shows one preferred method
for clocking the AD9262. A low jitter clock source is converted
from a single-ended signal to a differential signal using an RF
transformer. The back-to-back Schottky diodes across the
secondary side of the transformer limits clock excursions into the
AD9262 to approximately 0.8 V p-p differential. This helps
prevent the large voltage swings of the clock from feeding
through to other portions of the AD9262 while preserving the
fast rise and fall times of the signal, which are critical to
achieving low jitter.
If a differential clock is not available, the AD9262 can be driven
by a single-ended signal into the CLK+ terminal with the CLK−
terminal ac-coupled to ground. Figure 51 shows the circuit
configuration.
Another option is to ac couple a differential LVPECL signal to
the sample clock input pins, as shown in Figure 52. The AD951x
family of clock drivers is recommended because it offers excellent
jitter performance.
CLOCK
CLOCK
1
INPUT
INPUT
CLOCK
50Ω RESISTORS ARE OPTIONAL.
INPUT
CLOCK
INPUT
50Ω
Figure 50. Transformer-Coupled Differential Clock
1
50Ω
0.1µF
Figure 52. Differential LVPECL Sample Clock
50Ω
0.1µF
0.1µF
50Ω
1
Figure 51. Single-Ended Clock
TC1-1-13M+, 1:1
MINI-CIRCUITS
CLK
CLK
LVPECL
AD951x
DRIVER
0.1µF
XFMR
0.1µF
240Ω
0.1µF
0.1µF
0.1µF
SCHOTTKY
HSM2812
DIODES:
SCHOTTKY
HSM2812
DIODES:
240Ω
100Ω
CLK+
CLK–
0.1µF
0.1µF
CLK+
CLK–
CLK+
CLK–
AD9262
ADC
AD9262
AD9262
ADC
ADC