776535-3 TE Connectivity, 776535-3 Datasheet - Page 4
![AS 16, 3P CAP ASSY, RD, KEY 3](/photos/42/2/420226/pr776428_sml.jpg)
776535-3
Manufacturer Part Number
776535-3
Description
AS 16, 3P CAP ASSY, RD, KEY 3
Manufacturer
TE Connectivity
Specifications of 776535-3
Product Line
AMPSEAL 16
Product Type
Connector
Connector Type
Housing
Mount Angle
Straight
Mount
Mounting Clip
Housing Style
Clip Mount Rails
Mating Retention Type
Latching
Seal Type
Peripheral and Wire Seals
Centerline (mm [in])
4.50 [0.177]
Number Of Rows
1
Number Of Positions
3
Mating Retention
With
Fluid Type
Water
Contact Type
Pin
Contact Layout
In-Line
Connector Style
Receptacle
Mating Alignment
With
Housing Color
Yellow
Mating Alignment Type
Color Coded, Keyed, Terminal Position Assurance
Housing Material
Thermoplastic - GF
Environmental Protection
With
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Fluid Resistance
Immersion
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
776535-3
Manufacturer:
TE Connectivity AMP Connectors
Quantity:
103
Rev B
Therm al shock.
Sealing pressure.
Pressure washing.
Chem ical exposure.
Salt exposure.
Steam cleaning.
NOTE
Test Description
Shall meet visual requirements, show no physical damage, and meet requirements of additional
tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure
3.
See Note.
35 kPa, pre-test, no bubbles.
35 kPa, post-test, no bubbles.
See Note.
See Note.
See Note.
See Note.
Figure 2 (end)
Requirem ent
SAE J2030 6.13.
Subject specim ens to 10 cycles
between -40 and 120°C .with 1 hour
dwells at tem perature extrem es.
EIA-364-2.
Subject specim ens to specified
pressure for 30 m inutes.
SAE J2030 6.5. and SAE J1455
4.5.
Subject specim ens to spray for 3
seconds of a 6 second period for a
total of 375 cycles consisting of a
volum e of 9.46 liters per m inute at a
pressure of 7000 kPa and a
tem perature of 40°C from a
distance of 20 to 30 cm . No
detergent.
SAE J2030 6.14.
Subject specim ens to 5 cycles of a
5 m inute dip in the following
chem icals followed by air drying for
24 hours:
1) Diesel fuel at 60 ± 3°C;
2) Engine oil at 100 ± 3°C;
3) Transm ission drive train oil at
100 ± 3°C;
4) Final drive axle oil at 100 ± 3°C;
5) Ethylene glycol (50%) and water
(50%) at 100 ± 3°C;
6) Propylene glycol (50%) and
water (50%) at 100 ± 3°C;
7) Brake fluid at 25 ± 3°C.
SAE J2030 6.12. and ASTM B117.
Subject specim ens to a 5% salt
solution at 35°C for 96 hours.
SAE J1455 4.5.
Subject specim ens 375 cycles
lasting 18.75 m inutes of pressure
washing at 85°C consisting of a
volum e of 9.46 liters per m inute at a
pressure of 1400 kPa from a
distance of 20 to 30 cm . No
detergent.
Procedure
108-2184
4 of 6