AD9640BCPZ-150 Analog Devices Inc, AD9640BCPZ-150 Datasheet - Page 32
![IC ADC 14BIT 150MSP 1.8V 64LFCSP](/photos/6/50/65021/505-64-lfcsp_sml.jpg)
AD9640BCPZ-150
Manufacturer Part Number
AD9640BCPZ-150
Description
IC ADC 14BIT 150MSP 1.8V 64LFCSP
Manufacturer
Analog Devices Inc
Datasheet
1.AD9640ABCPZ-80.pdf
(52 pages)
Specifications of AD9640BCPZ-150
Design Resources
Interfacing ADL5534 to AD9640 High Speed ADC (CN0049)
Number Of Bits
14
Sampling Rate (per Second)
150M
Data Interface
Serial, SPI™
Number Of Converters
2
Power Dissipation (max)
938mW
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
For Use With
AD9640-150EBZ - BOARD EVALUATION AD9640 150MSPS
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9640
ADC OVERRANGE AND GAIN CONTROL
In receiver applications, it is desirable to have a mechanism to
reliably determine when the converter is about to be clipped.
The standard overflow indicator provides after-the-fact infor-
mation on the state of the analog input that is of limited usefulness.
Therefore, it is helpful to have a programmable threshold below
full scale that allows time to reduce the gain before the clip
actually occurs. In addition, because input signals can have
significant slew rates, latency of this function is of major concern.
Highly pipelined converters can have significant latency. A good
compromise is to use the output bits from the first stage of the
ADC for this function. Latency for these output bits is very low,
and overall resolution is not highly significant. Peak input signals
are typically between full scale and 6 dB to 10 dB below full
scale. A 3-bit or 4-bit output provides adequate range and
resolution for this function.
Using the SPI port, the user can provide a threshold above which
an overrange output is active. As long as the signal is below that
threshold, the output should remain low. The fast detect outputs
can also be programmed via the SPI port so that one of the pins
functions as a traditional overrange pin for customers who
currently use this feature. In this mode, all 14 bits of the converter
are examined in the traditional manner, and the output is high for
the condition normally defined as overflow. In either mode, the
magnitude of the data is considered in the calculation of the
condition (but the sign of the data is not considered). The threshold
detection responds identically to positive and negative signals
outside the desired range (magnitude).
FAST DETECT OVERVIEW
The AD9640 contains circuitry to facilitate fast overrange detec-
tion, allowing very flexible external gain control implementations.
Each ADC has four fast detect (FD) output pins that are used
to output information about the current state of the ADC input
level. The function of these pins is programmable via the fast detect
mode select bits and the fast detect enable bit in Register 0x104,
allowing range information to be output from several points in
the internal datapath. These output pins can also be set up to
indicate the presence of overrange or underrange conditions,
according to programmable threshold levels. Table 17 shows the
six configurations available for the fast detect pins.
Rev. B | Page 32 of 52
Table 17. Fast Detect Mode Select Bits Settings
Fast Detect
Mode Select Bits
(Register 0x104[3:1])
000
001
010
011
100
101
1
2
ADC FAST MAGNITUDE
When the fast detect output pins are configured to output the ADC
fast magnitude (that is, when the fast detect mode select bits are
set to 0b000), the information presented is the ADC level from
an early converter stage with a latency of only two clock cycles
(when in CMOS output mode). Using the fast detect output pins
in this configuration provides the earliest possible level indication
information. Because this information is provided early in the
datapath, there is significant uncertainty in the level indicated.
The nominal levels, along with the uncertainty indicated by the
ADC fast magnitude, are shown in Table 18.
Table 18. ADC Fast Magnitude Nominal Levels with Fast Detect
Mode Select Bits = 000
ADC Fast
Magnitude on
FD[3:0] Pins
0000
0001
0010
0011
0100
0101
0110
0111
1000
The fast detect pins are FD0A/FD0B to FD3A/FD3B for the CMOS mode
configuration and FD0+/FD0− to FD3+/FD3− for the LVDS mode configuration.
See the ADC Overrange (OR) and Gain Switching sections for more
information about OR, C_UT, F_UT, F_LT, IG, and DG.
Nominal Input
Magnitude
Below FS (dB)
<−24
−24 to −14.5
−14.5 to −10
−10 to −7
−7 to −5
−5 to −3.25
−3.25 to −1.8
−1.8 to −0.56
−0.56 to 0
FD3
ADC fast magnitude
ADC fast magnitude
Fast Detect (FD) Pins of Each ADC
OR
OR
(see Table 20)
(see Table 20)
ADC fast magnitude
Information Presented on
(see Table 19)
FD2
ADC fast magnitude
C_UT
F_UT
(see Table 18)
Nominal Input
Magnitude
Uncertainty (dB)
Minimum to −18.07
−18.07 to −8.52
−12.04 to −6.02
−6.02 to −2.5
−4.08 to −1.16
−2.5 to FS
−1.16 to 0
−30.14 to −12.04
−8.52 to −4.08
FD1
OR
C_UT
F_UT
IG
FD0
OR
F_LT
F_LT
F_LT
DG
1, 2