DS1866Z Maxim Integrated Products, DS1866Z Datasheet - Page 2
![IC POT TRIM LOG 2.7-5.5V 8-SOIC](/photos/1/39/13902/8-soic_21-0042b_sml.jpg)
DS1866Z
Manufacturer Part Number
DS1866Z
Description
IC POT TRIM LOG 2.7-5.5V 8-SOIC
Manufacturer
Maxim Integrated Products
Datasheet
1.DS1866Z.pdf
(5 pages)
Specifications of DS1866Z
Taps
8
Resistance (ohms)
10K
Number Of Circuits
1
Temperature Coefficient
750 ppm/°C Typical
Memory Type
Volatile
Interface
3-Input Parallel
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Resistance In Ohms
10K
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS1866Z
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS1866Z+
Manufacturer:
Renesas
Quantity:
320
Part Number:
DS1866Z+T&R
Manufacturer:
MAXIM/美信
Quantity:
20 000
OPERATION
The DS1866 is a single volatile potentiometer. The device has a total of eight positions providing a
resolution of 5 dB per step and giving a total attenuation range of 0 dB to -35 dB. These tap points are
accessible to the W-terminal whose position is controlled via a 3-terminal parallel port consisting of input
signals P0, P1, and P2. A block diagram of the DS1866 is shown in Figure 1.
Wiper position setting of the DS1866 is determined by the states of the P0, P1, and P2 input terminals.
Table 1 below outlines position setting versus value of the parallel port inputs. A Position-0 setting places
the wiper position at the L-terminal of the potentiometer and provides 35 dB of attenuation. As wiper
position increases, attenuation decreases with Position-7 giving 0 dB of attenuation.
On power-up, the wiper position of the DS1866 will be set to the P0, P1, and P2 values.
PIN DESCRIPTIONS
V
volts.
GND - Ground Terminal.
H - High-end Resistor. This is the high-end terminal of the potentiometer. It is not required that this
terminal be connected to a potential greater than the L-terminal. Maximum voltage on the H-terminal can
not exceed the power supply voltage, V
L - Low-end Resistor. This is the low-end terminal of the potentiometer. It is not required that this
terminal be connected to a potential less than the H-terminal. Maximum voltage on the L-terminal can not
exceed the power-supply voltage, V
W - Wiper of the Potentiometer. This pin is the wiper terminal of the potentiometer. Its position on the
resistor array is controlled by the 3-terminal parallel port. Maximum voltage on the W-terminal can not
exceed the power supply voltage, V
P0 - Bit 0. P0 is the bit 0 data input to the parallel port.
P1 - Bit 1. P1 is the bit 1 data input to the parallel port.
P2 - Bit 2. P2 is the bit 2 data input to the parallel port.
P2 P1 P0
CC
(binary)
000
001
010
011
100
101
110
111
- Power Supply Terminal. The DS1866 will support supply voltages ranging from +2.7 to +5.5
Position
Wiper
0
1
2
3
4
5
6
7
Attenuation
35 dB
30 dB
25 dB
20 dB
15 dB
10 dB
(dB)
5 dB
0 dB
CC
CC
, or go below ground.
, or go below ground.
CC
, or go below ground.
2 of 5
102199
DS1866