DS1845E-010+ Maxim Integrated Products, DS1845E-010+ Datasheet - Page 7
![IC POT/MEM DUAL NV 10K 14-TSSOP](/photos/6/57/65725/406-14-tssop_sml.jpg)
DS1845E-010+
Manufacturer Part Number
DS1845E-010+
Description
IC POT/MEM DUAL NV 10K 14-TSSOP
Manufacturer
Maxim Integrated Products
Datasheet
1.DS1845E-010.pdf
(14 pages)
Specifications of DS1845E-010+
Taps
100, 256
Resistance (ohms)
10K
Number Of Circuits
2
Temperature Coefficient
750 ppm/°C Typical
Memory Type
Non-Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
14-TSSOP
Resistance In Ohms
10K
Number Of Pots
Dual
Taps Per Pot
100
Resistance
10 KOhms
Wiper Memory
Non Volatile
Digital Interface
Serial (2-Wire)
Operating Supply Voltage
2.7 V to 5.5 V
Supply Current
40 uA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Tolerance
20 %
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The DS1845 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL respectively. After
2. Slave transmitter mode: The 1
Slave Address: command/control byte is the 1
master device. The command/control byte consists of a 4-bit control code. For the DS1845, this is set as
1010 binary for read/write operations. The next 3 bits of the command/ control byte are the device select
bits or slave address (A2, A1, A0). They are used by the master device to select which of eight devices is
to be accessed. When reading or writing the DS1845, the device-select bits must match the device-select
pins (A2, A1, A0). The last bit of the command/control byte (R/W) defines the operation to be performed.
When set to a 1 a read operation is selected, and when set to a 0 a write operation is selected.
Following the START condition, the DS1845 monitors the SDA bus checking the device type identifier
being transmitted. Upon receiving the 1010 control code, the appropriate device address bits, and the
read/write bit, the slave device outputs an acknowledge signal on the SDA line.
WRITE PROTECT
An external pin WP (write protect) protects EEPROM data and potentiometer position from alteration in
an application. This pin must be open or tied high to protect data from alteration.
READING AND WRITING THE POTENTIOMETER VALUES
Reading from and writing to the potentiometers consists of a standard read or write to EEPROM memory
at the addresses F8h and F9h. The 8-bit value at address F9h controls the wiper setting for potentiometer
0, which has 100 positions. The 8-bit value at address F8h controls the wiper setting of potentiometer 1,
which has 256 positions. Potentiometer 1 may be set to any value between 00h and FFh. 00h sets the
wiper of potentiometer 1 to its lowest value and FFh sets the wiper to its highest. Potentiometer 0 may be
set to any value between 00h and 63h. A value of 00h sets the wiper of potentiometer 0 to its lowest
position and 63h sets the wiper to its highest position. Any hexadecimal value is a valid address. Setting
a value greater than the upper limit of the potentiometer’s range, 64h or greater for potentiometer 0, will
result in setting the wiper to its highest position, but the MSB will be ignored.
each byte is received, an acknowledge bit is transmitted.
recognized as the beginning and end of a serial transfer. Address recognition is performed by
hardware after reception of the slave (device) address and direction bit.
in this mode the direction bit will indicate that the transfer direction is reversed. Serial data is
transmitted on SDA by the DS1845 while the serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and end of a serial transfer.
st
byte is received and handled as in the slave receiver mode. However,
st
byte received following the START condition from the
7 of 14
START and STOP conditions are