MAX5389LAUD+ Maxim Integrated Products, MAX5389LAUD+ Datasheet - Page 3

• Manufacturer Part Number: MAX5389LAUD+
• Description: IC POT DGTL 256-TAP 14TSSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX5389LAUD+

• Taps: 256
• Resistance (ohms): 10K
• Number Of Circuits: 2
• Temperature Coefficient: 35 ppm/°C Typical
• Memory Type: Volatile
• Interface: Up/Down
• Voltage - Supply: 2.6 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Resistance In Ohms: 10K
• Number Of Pots: Dual
• Taps Per Pot: 256
• Resistance: 200 Ohms
• Wiper Memory: Volatile
• Digital Interface: Up/Down
• Operating Supply Voltage: 2.6 V to 5.5 V
• Supply Current: 1 uA
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Description/function: Dual Up/Down Interface Digital Potentiometer
• Mounting Style: SMD/SMT
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.6 V
• Tolerance: 25 %
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ELECTRICAL CHARACTERISTICS (continued)
(V
T
Note 1: All devices are 100% production tested at T
Note 2: DNL and INL are measured with the potentiometer configured as a voltage-divider (Figure 1) with H_ = V
Note 3: R-DNL and R-INL are measured with the potentiometer configured as a variable resistor (Figure 1). DNL and INL are mea-
Note 4: The wiper resistance is the worst value measured by injecting the currents given in Note 3 into W_ with L_ = GND. R
Note 5: Drive HA with a 1kHz, GND to V
Note 6: The wiper-settling time is the worst case 0 to 50% rise time, measured between tap 0 and tap 127. H_ = V
Note 7: Digital timing is guaranteed by design and characterization, not production tested.
AC PERFORMANCE
Crosstalk
-3dB Bandwidth
Total Harmonic Distortion Plus
Noise
Wiper Settling Time (Note 6)
POWER SUPPLIES
Supply Voltage Range
Standby Current
DIGITAL INPUTS
Minimum Input High Voltage
Maximum Input Low Voltage
Input Leakage Current
Input Capacitance
TIMING CHARACTERISTICS (Note 7)
Maximum INC_ Frequency
CS to INC_ Setup Time
CS to INC_ Hold Time
INC_ Low Period
INC_ High Period
UD_ to INC_ Setup Time
UD_ to INC_ Hold Time
A
DD
= +25NC.) (Note 1)
= +2.6V to +5.5V, V
and characterization.
The wiper terminal is unloaded and measured with a high-input-impedance voltmeter.
sured with potentiometer configured as a variable resistor. H_ is unconnected and L_ = GND. For V
terminal is driven with a source current of 400µA for the 10kω configuration, 80µA for the 50kω configuration, and 40µA for
the 100kω configuration. For V
ration, 40µA for the 50kω configuration, and 20µA for the 100kω configuration.
(V
WB.
and the wiper terminal is loaded with 10pF capacitance to ground.
PARAMETER
W
- V
H
)/I
W
_______________________________________________________________________________________
.
H_
= V
Dual, 256-Tap, Volatile, Low-Voltage
DD
Linear Taper Digital Potentiometer
, V
SYMBOL
THD+N
DD
L_
f
V
BW
V
MAX
V
t
t
t
t
t
t
DD
t
DD
CI
IC
IH
DI
ID
IL
S
IH
IL
= 0, T
= +2.6V, the wiper terminal is driven with a source current of 200µA for the 10kω configu-
amplitude, tone. LA = LB = GND. No load. WB is at midscale with a 10pF load. Measure
(Note 5)
Code = 80H, 10pF load,
V
Measured at W, V
MAX5389L
MAX5389M
MAX5389N
Digital inputs = V
A
DD
= -40NC to +125NC, unless otherwise noted. Typical values are at V
= +2.6V
A
= +25NC. Specifications over temperature limits are guaranteed by design
CONDITIONS
DD
H
_ = 1V
or GND
MAX5389L
MAX5389M
MAX5389N
RMS
at 1kHz
MIN
2.6
70
25
25
25
50
-1
0
0
0.015
1000
2000
TYP
600
150
300
-90
75
1
5
DD
DD
MAX
= +5V, the wiper
5.5
+1
30
10
and L_ = GND.
DD
, L_ = GND,
DD
% x V
% x V
UNITS
MHz
= +5V,
kHz
dB
FA
FA
pF
ns
ns
ns
ns
ns
ns
ns
%
V
W
DD
DD
3
=