MCP4021T-103E/MS Microchip Technology, MCP4021T-103E/MS Datasheet - Page 33
![IC DGTL POT 10K 1CH 8MSOP](/photos/6/59/65932/mfg_150_c04-111_ms_8-msop_sml.jpg)
MCP4021T-103E/MS
Manufacturer Part Number
MCP4021T-103E/MS
Description
IC DGTL POT 10K 1CH 8MSOP
Manufacturer
Microchip Technology
Specifications of MCP4021T-103E/MS
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Taps
64
Resistance (ohms)
10K
Number Of Circuits
1
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
Up/Down
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Resistance In Ohms
10K
Number Of Pots
Single
Taps Per Pot
64
Resistance
10 KOhms
Wiper Memory
Non Volatile
Digital Interface
Serial (2-Wire)
Operating Supply Voltage
3.3 V, 5 V
Supply Current
45 uA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MCP4XXXDM-DB - BOARD DAUGHTER DIGIPOT MCP4XXXMCP402XEV - BOARD EVAL FOR MCP402X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP4021T-103E/MS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
5.2.4
This mode is achieved by initializing the U/D pin to a
low state (V
CS pin. Subsequent rising edges of the U/D pin
decrement the wiper setting (toward terminal B). This is
shown in
After the wiper is decremented to the desired position,
the U/D pin should remain high (V
CS pin is raised to V
EEPROM. Therefore, if the device voltage is lowered
below the RAM retention voltage of the device, once
the device returns to the operating range, the wiper will
be loaded with this wiper setting (stored in the
EEPROM).
FIGURE 5-4:
© 2006 Microchip Technology Inc.
WiperLock™ Technology
Figure
IL
DECREMENT WITH WRITING
WIPER SETTING TO EEPROM
) prior to achieving a low state (V
5-4.
IH
EEPROM
, the wiper value is written to the
Decrement with Writing Wiper Setting to EEPROM.
Wiper
U/D
CS
Note: If WiperLock technology enabled, wiper will not change.
IH
V
). Then when the
IL
V
IL
X
X
IL
1
) on the
X-1
X
2
X-2
X
3
To ensure that “unexpected” transitions on the U/D pin
do not cause the wiper setting to decrement, the U/D
pin should be driven low (V
V
after the last desired increment occurs.
After the CS pin is driven to V
serial commands are ignored until the EEPROM write
cycle (t
X-3
IH
X
Note:
as soon as possible (within device specifications)
4
WC
X-4
X
) completes.
The wiper value will not underflow. That is,
once the wiper value equals 0x00,
subsequent decrement commands are
ignored.
t
WC
WiperLock Technology Enable
WiperLock Technology Disable
MCP4021/2/3/4
X-4
5
IL
) and the CS pin forced to
IH
6
(from V
V
DS21945E-page 33
V
IH
IH
IL
), all other