AD5241BRU10-REEL7 Analog Devices Inc, AD5241BRU10-REEL7 Datasheet - Page 15
![IC DGTL POT 256POS 14-TSSOP T/R](/photos/6/60/66047/ru-14_sml.jpg)
AD5241BRU10-REEL7
Manufacturer Part Number
AD5241BRU10-REEL7
Description
IC DGTL POT 256POS 14-TSSOP T/R
Manufacturer
Analog Devices Inc
Datasheet
1.AD5242BRUZ100-RL7.pdf
(20 pages)
Specifications of AD5241BRU10-REEL7
Rohs Status
RoHS non-compliant
Taps
256
Resistance (ohms)
10K
Number Of Circuits
1
Temperature Coefficient
30 ppm/°C Typical
Memory Type
Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V, ±2.3 V ~ 2.7 V
Operating Temperature
-40°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
14-TSSOP
Resistance In Ohms
10K
Number Of Elements
1
# Of Taps
256
Resistance (max)
10KOhm
Power Supply Requirement
Single/Dual
Interface Type
Serial (2-Wire/I2C)
Single Supply Voltage (typ)
3/5V
Dual Supply Voltage (typ)
±2.5V
Single Supply Voltage (min)
2.7V
Single Supply Voltage (max)
5.5V
Dual Supply Voltage (min)
±2.3V
Dual Supply Voltage (max)
±2.7V
Operating Temp Range
-40C to 105C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
14
Lead Free Status / Rohs Status
Not Compliant
ADDITIONAL PROGRAMMABLE LOGIC OUTPUT
The AD5241/AD5242 feature additional programmable logic
outputs, O
switches, and logic gates. They can also be used as a self-contained
shutdown preset to Logic 0 that is further explained in the
Shutdown Function section. O
power-up. The logic states of O
Frame 2 under the write mode (see Figure 4). Figure 34 shows
the output stage of O
channel MOSFETs in push-pull configuration. As shown in
Figure 34, the output is equal to V
outputs have adequate current driving capability to drive
milliamperes of load.
Users can also activate O
ways without affecting the wiper settings:
1.
2.
3.
All digital inputs are protected with a series input resistor and
the parallel Zener ESD structures shown in Figure 36. This
applies to the digital input pins, SDA, SCL, and SHDN .
Start, slave address byte, acknowledge, instruction byte
with O
Complete the write cycle with stop, then start, slave address
byte, acknowledge, instruction byte with O
acknowledge, stop.
Do not complete the write cycle by not issuing the stop,
then start, slave address byte, acknowledge, instruction
byte with O
1
1
and O
and O
Figure 34. Output Stage of Logic Output, O
IN
O
OF WRITE MODE
1
1
DATA IN FRAME 2
and O
2
, that can be used to drive digital load, analog
2
specified, acknowledge, stop.
1
, which employs large P-channel and N-
1
1
2
and O
specified, acknowledge, stop.
1
2
2
1
and O
in the following three different
and O
DD
M
M
P
N
or V
2
2
default to Logic 0 during
V
V
can be programmed in
DD
SS
SS
, and these logic
O
1
1
and O
1
2
specified,
Rev. C | Page 15 of 20
SHUTDOWN FUNCTION
Shutdown can be activated by strobing the SHDN pin or
programming the SD bit in the write mode instruction byte (see
Table 2
only) is placed in shutdown mode by the software, SD bit, the
part returns the wiper to its prior position when a new command
is received.
In addition, shutdown can be implemented with the device digital
output, as shown in Figure 35. In this configuration, the device
is shutdown during power-up but users are allowed to program
the device. Thus, when O
shutdown mode and responds to the new setting. This self-contained
shutdown function allows absolute shutdown during power-up,
which is crucial in hazardous environments, and it does not add
extra components.
). If the RDAC Register 1 or RDAC Register 2 (AD5242
Figure 35. Shutdown by Internal Logic Output, O
Figure 37. ESD Protection of Resistor Terminals
Figure 36. ESD Protection of Digital Pins
R
340
PD
A,B,W
1
Ω
is programmed high, the device exits
V
V
SS
O
SHDN
SDA
SCL
SS
1
LOGIC
AD5241/AD5242
1