HW1K-3AF11 IDEC, HW1K-3AF11 Datasheet - Page 61
![no-image](/images/no-image-200.jpg)
HW1K-3AF11
Manufacturer Part Number
HW1K-3AF11
Description
Key Selector Switch 22mm Maintained 3-Position 1NO-1NC
Manufacturer
IDEC
Datasheet
1.HW1A-B1-R.pdf
(61 pages)
Specifications of HW1K-3AF11
Contact Configuration
SPDT-1NO / 1NC
Actuator Style
Flat
No. Of Switch Positions
3
Contact Voltage Ac Nom
600V
Contact Voltage Dc Nom
220V
Contact Current Max
10A
560
Replacement of Lamps
Lamps can be replaced by using the lamp holder tool (OR-55) from the front of
the panel, or by removing the contact block assembly from the operator unit.
Removing the Lamps from the Front of the Panel
Removal
Installation
About Pushbutton Switches
Narrow Mounting
When mounting the units closely in a horizontal row on 30mm centers, use op-
tional barriers to prevent interconnection between adjoining terminals. The barri-
ers can be attached simply by pressing them onto the sides of contact blocks.
1. To remove, slip the lamp
1. To install, insert the lamp
2. Place the pins on the lamp
The pushbuttons cannot be
removed or replaced!
Do not attempt to remove
using a flat screwdriver or pin-
cers, otherwise the pushbut-
tons may be damaged.
When mounting transformer type illuminated
units closely in a horizontal row on 30-mm
centers, insert solid wires or stranded wires
into inside of the terminal screw on the
transformer (see figure on the right) to prevent
short circuit between adjoining terminals.
holder tool onto the lamp
head lightly. Then push
slightly, and turn the lamp
holder tool counterclock-
wise.
head into the lamp holder
tool, and hold the lamp as
shown in the figure below.
base to the grooves in the
lamp socket. Insert the lamp
and turn it clockwise.
ø22mm - HW Series
Pushbuttons
Lamp
Lamp Base
X1
Dual Pushbuttons Instructions con’t
Lamp Holder Tool
Inside Inside
30
Do not attempt
to remove the
pushbuttons!
Barrier
X2
X1
30
X2
www.idec.com
Tightening Torque for Terminal Screws
Tighten the M3.5 terminal screws to a torque of 1.0 to 1.3 N·m.
Installation of LED Illuminated Units
When using full voltage type LED illuminated units, provide protection against
electrical noise, if necessary.
Applicable Wiring
The applicable wire size is 2 mm
or two wires can be connected.
Applicable Crimping Terminal
Be sure to use an insulation tube or cover on the crimping part of the crimping
terminal to prevent electrical shocks.
Solid Wire
Note: When connecting wires to contact blocks or transformers in the direction
shown below, keep the insulation stripping length 6.6 mm at the maximum.
Installing the Rubber Cover
When using the HW7D pushbuttons in places where the pushbuttons are
subjected to water splash or an excessive amount of dust, make sure to use the
HW9Z-D7D rubber boot (IP65) which is ordered separately.
Notes for Installing the Rubber Cover
Remove the gasket from the operator, and install the rubber boot on the operator.
Pull out the seals of the rubber boot and place them around the operator sleeve
as shown. Make sure that the seals are not twisted or tucked inside and that
the gasket does not remain, otherwise the normal waterproof and dustproof
characteristics are not ensured.
1. Remove the gasket.
4 max.
Gasket
Remove
ø3.6 min.
8 max.
5.5 min.
Oiltight Switches & Pilot Devices
2. Install the rubber boot
on the pushbuttons.
Seals
Seals
2
maximum. (solid wire ø1.6mm
X1
Install
Inside Inside
X2
X1
3. Rubber boot is
installed.
X2
2
maximum) One