AD5443YRMZ Analog Devices Inc, AD5443YRMZ Datasheet - Page 5

• Manufacturer Part Number: AD5443YRMZ
• Description: IC DAC 12BIT SERIAL IOUT 10-MSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5443YRMZ

• Data Interface: Serial
• Design Resources: Unipolar, Precision DC Digital-to-Analog Conversion Using AD5426/32/43 8-Bit to12-Bit DACs (CN0034) Precision, Bipolar Configuration for the AD5426/32/43 8-Bit to12-Bit DACs (CN0036) AC Signal Processing Using AD5426/32/43 Current Output DACs (CN0037) Programmable Gain Element Using AD5426/32/43 Current Output DACs (CN0038) Single-Ended-to-Differential Converters for Voltage Output and Current Output DACs Using AD8042 (CN0143)
• Number Of Bits: 12
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Power Dissipation (max): 25µW
• Settling Time: 50ns
• Resolution (bits): 12bit
• Sampling Rate: 2.5MSPS
• Input Channel Type: Serial
• Supply Voltage Range - Analog: 3V To 5.5V
• Supply Current: 400nA
• Digital Ic Case Style: SOP
• Number Of Channels: 1
• Resolution: 12b
• Interface Type: SER 3W SPI QSPI UW
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Architecture: R-2R
• Power Supply Requirement: Single
• Output Type: Current
• Single Supply Voltage (min): 3V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 10
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD5443-DBRDZ - BOARD EVAL CARD CLINUX/STAMP
• Lead Free Status / Rohs Status: Compliant

TIMING CHARACTERISTICS
All input signals are specified with tr = tf = 1 ns (10% to 90% of V
V
Table 2.
Parameter
f
t
t
t
t
t
t
t
t
t
1
2
SCLK
1
2
3
4
5
6
7
8
9
Falling or rising edge as determined by control bits of serial word.
Daisy-chain and readback modes cannot operate at maximum clock frequency. SDO timing specifications measured with load circuit, as shown in Figure 4.
1
2
REF
= 10 V, I
SCLK
SYNC
SYNC
SDIN
SCLK
SDO
DIN
ALTERNATIVELY, DATA MAY BE CLOCKED INTO INPUT SHIFT REGISTER ON RISING EDGE OF
SCLK AS DETERMINED BY CONTROL BITS. TIMING AS PER ABOVE, WITH SCLK INVERTED.
ALTERNATIVELY, DATA MAY BE CLOCKED INTO INPUT SHIFT REGISTER ON RISING EDGE OF SCLK AS
DETERMINED BY CONTROL BITS. IN THIS CASE, DATA WOULD BE CLOCKED OUT OF SDO ON FALLING
EDGE OF SCLK. TIMING AS PER ABOVE, WITH SCLK INVERTED.
OUT
2 = 0 V; temperature range for Y version: −40°C to +125°C; all specifications T
2.5 V to 5.5 V
50
20
8
8
13
5
3
5
30
80
120
t
8
t
4
t
DB15 (N)
4
DB15
t
5
t
5
t
t6
6
4.5 V to 5.5 V
50
20
8
8
13
5
3
5
30
45
65
t
6
Figure 3. Daisy-Chain and Readback Modes Timing Diagram
t
2
Figure 2. Standalone Mode Timing Diagram
t
2
Unit
MHz max
ns min
ns min
ns min
ns min
ns typ
ns min
ns min
ns min
ns min
ns max
t
1
t
3
Rev. C | Page 5 of 28
t
1
t
3
DB0 (N)
DD
) and timed from a voltage level of (V
t
9
DB0
DB15(N)
t
(N + 1)
7
DB15
Conditions/Comments
Max clock frequency
SCLK cycle time
SCLK high time
SCLK low time
SYNC falling edge to SCLK active edge setup time
Data setup time
Data hold time
SYNC rising edge to SCLK active edge
Minimum SYNC high time
SCLK active edge to SDO valid

MIN
to T
AD5426/AD5432/AD5443
MAX
IL
, unless otherwise noted.
+ V
IH
DB0(N)
)/2. V
(N + 1)
DB0
t
7
DD
= 2.5 V to 5.5 V,
t
8