646502-1 TE Connectivity, 646502-1 Datasheet

2MM HM DUST PROTECTOR TYPE A/B

646502-1

Manufacturer Part Number
646502-1
Description
2MM HM DUST PROTECTOR TYPE A/B
Manufacturer
TE Connectivity
Type
Type A, Type Br
Datasheets
1.5646442-1.pdf (10 pages)
2.646502-2.pdf (1 pages)

Specifications of 646502-1

Rohs Compliant
YES
Product Type
Accessories
Mounting Style
PCB
Accessory Type
Pin Cover
Gender
Plug
Used For
PCB Mount Connectors
Module Length (mm [in])
49.23 [1.940]
Compactpci
No
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Lead Free Status / Rohs Status
 Details
1.
1.1.
1.2.
2.
2.1.
2.2.
3.
3.1.
3.2.
3.3.
©2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. Company
All Rights Reserved
TE logo is a trademark.
SCOPE
Content
This specification covers performance, tests and quality requirements for the Z-PACK* 8 row, 2mm HM
connector system. These connectors are two-piece devices to interconnect 2 printed circuit boards.
Receptacle and pin connectors are through hole devices with ACTION PIN* contacts. Connectors are in
8 row configurations and can be upgraded to 10 row configuration.
Qualification
When tests are performed on subject product line, procedures specified in IEC 512 (see Figure 8) shall
be used. All inspections shall be performed using applicable inspection plan and product drawing.
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, latest edition of the document applies. In the event of conflict between
requirements of this specification and product drawing, product drawing shall take precedence. In the
event of conflict between requirements of this specification and referenced documents, this specification
shall take precedence.
TE Connectivity (TE) Document
501-326: Qualification Test Report
Commercial Standards
IEC 512: Test Specification
REQUIREMENTS
Design and Construction
Product shall be of design, construction and physical dimensions specified on applicable product
drawing.
Materials
!
!
!
Ratings
!
!
!
!
Coding devices: Polyamide 35% GF, UL94HB
Contact: Phosphor bronze, gold over nickel plating in contact area
Housing: Thermoplastic polyester, 20% GF, UL94V-0
Voltage: 750 vrms contact to contact
Current: Signal application only, 1.5 amperes per contact at 70° C (fully loaded)
Temperature:
Air/creepage distance:
| Indicates change
*Trademark
Product
Specification
Connector, Z-PACK*, 8 Row, 2mm HM
-55 to 125° C
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
0.8mm minimum
108-1622
11Mar11 Rev A
1 of 10
LOC B

646502-1 Summary of contents

Page 1

... Temperature: -55 to 125° Air/creepage distance: ©2011 Tyco Electronics Corporation, | Indicates change a TE Connectivity Ltd. Company *Trademark All Rights Reserved TE logo is a trademark. 0.8mm minimum For latest revision, visit our website at www.te.com/documents. For Regional Customer Service, visit our website at www.te.com Other products, logos, and company names might be trademarks of their respective owners. ...

Page 2

Performance and Test Description Product is designed to meet electrical, mechanical and environmental performance requirements specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental conditions per IEC 512-1. 3.5. Test Requirements and Procedures ...

Page 3

Test Description Polarization force. Mating force. Unmating force. Contact retention force. Module retention force. ACTION PIN contact retention force. Gage retention force. Durability. Thermal shock. Humidity-temperature cycling. Humidity, steady state. Rev A Requirement 100 Newtons (22.48 pounds) minimum. See Note. ...

Page 4

Test Description Corrosion atmosphere. Temperature life and electrical load. See Note. Shall meet visual requirements, show no physical damage and shall meet requirements of NOTE additional tests as specified in Test Sequence in Figure 2. Rev A Requirement See Note. ...

Page 5

Product Qualification and Requalification Test Sequence Test or Examination Examination of product Termination resistance Dielectric withstanding voltage Insulation resistance Vibration Physical shock Polarization force Mating force Unmating force Contact retention force Module retention force ACTION PIN contact retention force ...

Page 6

QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Sample Selection Samples shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test groups and 5 shall each consist ...

Page 7

Dielectric Withstanding Voltage Wiring Arrangement Rev A Figure 3 Termination Resistance Measurement Points Figure 4 108-1622 ...

Page 8

Vibration & Physical Shock Mounting Fixture Rev A Figure 5 Figure 6 Module Retention Force 108-1622 ...

Page 9

Retention Force Rev A Application “A” Dimension Sizing 0.04 to 0.39 0.36 to 0.35 Figure 7 Gage Retention Force 108-1622 Mass (grams ...

Page 10

Test Examination of product Termination resistance Dielectric withstanding voltage Insulation resistance Vibration Physical Shock Polarization force Mating force Unmating force Contact retention force Module retention force ACTION PIN contact retention force Gage retention force Durability Thermal shock Humidity-temperature cycling Humidity, ...