LTC2630ISC6-HZ10#TRPBF Linear Technology, LTC2630ISC6-HZ10#TRPBF Datasheet - Page 13
![IC DAC 10BIT R-R SC70-6](/photos/6/67/66780/sc70-6_05-08-1638_rev_b_sml.jpg)
LTC2630ISC6-HZ10#TRPBF
Manufacturer Part Number
LTC2630ISC6-HZ10#TRPBF
Description
IC DAC 10BIT R-R SC70-6
Manufacturer
Linear Technology
Datasheet
1.LTC2630CSC6-LZ8TRMPBF.pdf
(20 pages)
Specifications of LTC2630ISC6-HZ10#TRPBF
Settling Time
3.9µs
Number Of Bits
10
Data Interface
Serial
Number Of Converters
1
Voltage Supply Source
Single Supply
Power Dissipation (max)
480µW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
SC-70-6, SC-88, SOT-363
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
TIMING DIAGRAM
OPERATION
The LTC2630 is a family of single voltage output DACs in
6-lead SC70 packages. Each DAC can operate rail-to-rail
referenced to the input supply, or with its full-scale voltage
set by an integrated reference. Twelve combinations of
accuracy (12-, 10-, and 8-bit), power-on reset value (zero
or mid-scale), and full-scale voltage (2.5V or 4.096V)
are available. The LTC2630 is controlled using a 3-wire
SPI/MICROWIRE compatible interface.
Power-On Reset
The LTC2630-HZ/-LZ clear the output to zero scale when
power is fi rst applied, making system initialization con-
sistent and repeatable.
For some applications, downstream circuits are active
during DAC power-up, and may be sensitive to nonzero
outputs from the DAC during this time. The LTC2630
contains circuitry to reduce the power-on glitch: the
analog output typically rises less than 5mV above zero
scale during power on if the power supply is ramped
to 5V in 1ms or more. In general, the glitch amplitude
decreases as the power supply ramp time is increased.
See “Power-On Reset Glitch” in the Typical Performance
Characteristics section.
The LTC2630-HM/-LM provide an alternative reset, setting
the output to mid-scale when power is fi rst applied.
CS/LD
SCK
SDI
t
5
t
7
t
1
t
2
1
Figure 1. Serial Interface Timing
t
3
2
Transfer Function
The digital-to-analog transfer function is
where k is the decimal equivalent of the binary DAC
input code, N is the resolution, and V
(LTC2630-L) or 4.096V (LTC2630-H) in internal refer-
ence mode, and V
Table 1. Command Codes
*Command codes not shown are reserved and should not be used.
Command*
C3 C2 C1 C0
0
0
0
0
0
0
t
4
V
OUT(IDEAL)
0
0
0
1
1
1
3
0
0
1
0
1
1
0
1
1
0
0
1
=
Write to Input Register
Update (Power up) DAC Register
Write to and Update (Power up) DAC Register
Power down
Select Internal Reference (Power-on Reset Default)
Select Supply as Reference (V
2
k
N
23
CC
V
in Supply as reference mode.
REF
t
6
24
t
10
REF
LTC2630
REF
= V
is either 2.5V
CC
)
2630 F01
13
2630fe