LTC2636IDE-HMI8#PBF Linear Technology, LTC2636IDE-HMI8#PBF Datasheet - Page 15
![IC DAC 8BIT OCTAL VOUT 14-DFN](/photos/6/62/66298/14-dfn_05-08-1708_rev_b_sml.jpg)
LTC2636IDE-HMI8#PBF
Manufacturer Part Number
LTC2636IDE-HMI8#PBF
Description
IC DAC 8BIT OCTAL VOUT 14-DFN
Manufacturer
Linear Technology
Datasheet
1.LTC2636IDE-HMI12PBF.pdf
(24 pages)
Specifications of LTC2636IDE-HMI8#PBF
Settling Time
3.8µs
Number Of Bits
8
Data Interface
MICROWIRE™, Serial, SPI™
Number Of Converters
8
Voltage Supply Source
Single Supply
Power Dissipation (max)
2.7mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
14-DFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
PIN FUNCTIONS
V
(LTC2636-L) or 4.5V ≤ V
to GND with a 0.1μF capacitor.
V
Analog Voltage Outputs.
CS/LD (Pin 6/7): Serial Interface Chip Select/Load Input.
When CS/LD is low, SCK is enabled for shifting data on
SDI into the register. When CS/LD is taken high, SCK
is disabled and the specifi ed command (see Table 1) is
executed.
SCK (Pin 7/8): Serial Interface Clock Input. CMOS and
TTL compatible.
SDI (Pin 8/9): Serial Interface Data Input. Data on SDI is
clocked into the DAC on the rising edge of SCK. The LTC2636
accepts input word lengths of either 24 or 32 bits.
REF (Pin 9/11): Reference Voltage Input or Output. When
External Reference mode is selected, REF is an input
(1V ≤ V
full-scale DAC output voltage. When Internal Reference
is selected, the 10ppm/°C 1.25V (LTC2636-L) or 2.048V
(LTC2636-H) internal reference (half full-scale) is avail-
able at REF. This output may be bypassed to GND with
up to 10μF , and must be buffered when driving external
DC load current.
CC
OUT
(Pin 1/1): Supply Voltage Input. 2.7V ≤ V
A to V
REF
≤ V
OUT
CC
H (Pins 2-5, 10-13/2-5, 12-15): DAC
) where the voltage supplied sets the
CC
(DFN/MSOP)
≤ 5.5V (LTC2636-H). Bypass
CC
≤ 5.5V
GND (Pin 14/16): Ground.
LDAC (Pin 6, MSOP only): Asynchronous DAC Update
Pin. If CS/LD is high, a falling edge on LDAC immediately
updates the DAC registers with the contents of the input
registers (similar to a software update). If CS/LD is low
when LDAC goes low, the DAC registers are updated after
CS/LD returns high. A low on the LDAC pin powers up
the DACs. A software power down command is ignored if
LDAC is low. If the LDAC functionality is not being used,
the LDAC pin should be tied high.
CLR (Pin 10, MSOP only): Asynchronous Clear Input.
A logic low at this level-triggered input clears all regis-
ters and causes the DAC voltage output to reset to Zero
(LTC2636-Z) or Mid-scale (LTC2636-MI/-MX). CMOS and
TTL compatible.
Exposed Pad (Pin 15, DFN Only): Ground. Must be sol-
dered to PCB Ground.
LTC2636
15
2636fb