LTC2610IGN#TR Linear Technology, LTC2610IGN#TR Datasheet - Page 12
![IC DAC R-R 14-BIT OCTAL 16-SSOP](/photos/6/59/65965/161-16-ssop_sml.jpg)
LTC2610IGN#TR
Manufacturer Part Number
LTC2610IGN#TR
Description
IC DAC R-R 14-BIT OCTAL 16-SSOP
Manufacturer
Linear Technology
Datasheet
1.LTC2620CUFDPBF.pdf
(20 pages)
Specifications of LTC2610IGN#TR
Settling Time
9µs
Number Of Bits
14
Data Interface
Serial
Number Of Converters
8
Voltage Supply Source
Single Supply
Power Dissipation (max)
20mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
OPERATION
LTC2600/LTC2610/LTC2620
Power-On Reset
The LTC2600/LTC2610/LTC2620 clear the outputs to
zero-scale when power is fi rst applied, making system
initialization consistent and repeatable.
For some applications, downstream circuits are active during
DAC power-up, and may be sensitive to nonzero outputs
from the DAC during this time. The LTC2600/2610/2620
contain circuitry to reduce the power-on glitch: the analog
outputs typically rise less than 10mV above zero-scale
during power on if the power supply is ramped to 5V in 1ms
or more. In general, the glitch amplitude decreases as the
power supply ramp time is increased. See Power-On Reset
Glitch in the Typical Performance Characteristics section.
Power Supply Sequencing
The voltage at REF (Pin 6) should be kept within the
range –0.3V ≤ V
Ratings). Particular care should be taken to observe these
limits during power supply turn-on and turn-off sequences,
when the voltage at V
Transfer Function
The digital-to-analog transfer function is:
where k is the decimal equivalent of the binary DAC
input code, N is the resolution and V
REF (Pin 6).
Table 1.
COMMAND*
*Command and address codes not shown are reserved and should not be used.
12
C3
0
0
0
0
0
1
V
OUT IDEAL
C2
0
0
0
0
1
1
(
C1
0
0
1
1
0
1
C0
)
0
1
0
1
0
1
=
REF
⎛
⎝ ⎜
Write to Input Register n
Update (Power Up) DAC Register n
Write to Input Register n, Update (Power Up) All n
Write to and Update (Power Up) n
Power Down n
No Operation
2
k
≤ V
N
CC
⎞
⎠ ⎟
CC
V
(Pin 16) is in transition.
REF
+ 0.3V (see Absolute Maximum
REF
is the voltage at
Serial Interface
The CS/LD input is level triggered. When this input is taken
low, it acts as a chip-select signal, powering on the SDI and
SCK buffers and enabling the input shift register. Data (SDI
input) is transferred at the next 24 rising SCK edges. The
4-bit command, C3-C0, is loaded fi rst; then the 4-bit DAC
address, A3-A0; and fi nally the 16-bit data word. The data
word comprises the 16-, 14- or 12-bit input code, ordered
MSB-to-LSB, followed by 0, 2 or 4 don’t-care bits (LTC2600,
LTC2610 and LTC2620 respectively). Data can only be
transferred to the device when the CS/LD signal is low.The
rising edge of CS/LD ends the data transfer and causes the
device to carry out the action specifi ed in the 24-bit input
word. The complete sequence is shown in Figure 2a.
The command (C3-C0) and address (A3-A0) assignments
are shown in Table 1. The fi rst four commands in the table
consist of write and update operations. A write operation
loads a 16-bit data word from the 32-bit shift register
into the input register of the selected DAC, n. An update
operation copies the data word from the input register to
the DAC register. Once copied into the DAC register, the
data word becomes the active 16-, 14- or 12-bit input
code, and is converted to an analog voltage at the DAC
output. The update operation also powers up the selected
DAC if it had been in power-down mode. The data path
and registers are shown in the Block Diagram.
While the minimum input word is 24 bits, it may optionally
be extended to 32 bits. To use the 32-bit word width, 8
don’t-care bits are transferred to the device fi rst, followed
by the 24-bit word as just described. Figure 2b shows the
ADDRESS (n)*
A3
0
0
0
0
0
0
0
0
1
A2
0
0
0
0
1
1
1
1
1
A1
0
0
1
1
0
0
1
1
1
A0
0
1
0
1
0
1
0
1
1
DAC A
DAC B
DAC C
DAC D
DAC E
DAC F
DAC G
DAC H
All DACs
2600fe