LM4895LDX National Semiconductor, LM4895LDX Datasheet - Page 4

• Manufacturer Part Number: LM4895LDX
• Manufacturer: National Semiconductor

Specifications of LM4895LDX

• Operational Class: Class-AB
• Audio Amplifier Output Configuration: 1-Channel Mono
• Output Power (typ): 1.4x1@4OhmW
• Audio Amplifier Function: Speaker
• Total Harmonic Distortion: 0.1@8Ohm@400mW%
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Single
• Rail/rail I/o Type: No
• Power Supply Rejection Ratio: 84dB
• Single Supply Voltage (min): 2.2V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 10
• Package Type: LLP
• Lead Free Status / Rohs Status: Not Compliant

www.national.com
Electrical Characteristics V
The following specifications apply for V
25˚C. (Continued)
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
allowable power dissipation is P
currents for additional information.
Note 4: Human body model, 100pF discharged through a 1.5kΩ resistor.
Note 5: Machine Model, 220pF–240pF discharged through all pins.
Note 6: Typicals are measured at 25˚C and represent the parametric norm.
Note 7: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 8: For micro SMD only, shutdown current is measured in a Normal Room Environment. Exposure to direct sunlight will increase I
Note 9: Unterminated input.
Note 10: 10Ω terminated input.
Note 11: When driving 4Ω loads from a 5V supply, the LM4895LD must be mounted to a circuit board.
External Components Description
Typical Performance Characteristics
LD Specific Characteristics
Components
1.
2.
C
C
S
B
THD+N vs Output Power
Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing
section for information concerning proper placement and selection of the supply bypass capacitor.
Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of External
Components, for information concerning proper placement and selection of C
V
DD
DMAX
LM4895LD
= 5V, 4Ω R
= (T
JMAX
–T
L
A
DD
)/θ
JA
= 3V and 8Ω load unless otherwise specified. Limits apply for T
or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4895, see power derating
DD
20023202
= 3V
(Notes 1, 2, 8)
(Figure 1)
Functional Description
4
V
DD
JMAX
= 5V, 4Ω R
THD+N vs Frequency
, θ
JA
, and the ambient temperature T
LM4895LD
L
, and Power = 1W
B
.
A
SD
=
by a maximum of 2µA.
20023210
A
. The maximum