SLCF512M2PUI STEC, SLCF512M2PUI Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
SLCF512M2PUI
Manufacturer Part Number
SLCF512M2PUI
Description
Manufacturer
STEC
Type
CompactFlashr
Datasheet
1.SLCF512M2PUI.pdf
(56 pages)
Specifications of SLCF512M2PUI
Density
512MByte
Operating Supply Voltage (typ)
3.3/5V
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Package Type
Not Required
Pin Count
50
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.97/4.5V
Operating Supply Voltage (max)
3.63/5.5V
Programmable
Yes
Lead Free Status / Rohs Status
Compliant
SLCFxxx(G)M2PU(I)
Datasheet
-WAIT
(PC Card Memory Mode
except UDMA protocol
active)
-DDMARDY
(All Modes: UDMA Write
protocol active)
DSTROBE
(All Modes: UDMA Read
protocol active)
-WAIT
(PC Card I/O Mode except
UDMA protocol active)
-DDMARDY
(All Modes: UDMA Write
protocol active)
DSTROBE
(All Modes: UDMA Read
protocol active)
IORDY
(True IDE Mode except
UDMA protocol active)
-DDMARDY
(All Modes: UDMA Write
protocol active)
DSTROBE
(All Modes: UDMA Read
protocol active)
GND
(PC Card Memory Mode)
GND
(PC Card I/O Mode)
GND
(True IDE Mode)
VCC
(PC Card Memory Mode)
VCC
(PC Card I/O Mode)
VCC
(True IDE Mode)
RESET
(PC Card Memory Mode)
RESET
(PC Card I/O Mode)
-RESET
(True IDE Mode)
-VS1
-VS2
(PC Card Memory Mode)
O
GND
VCC
I
O
42
1, 50
13, 38
41
33, 40
61000-05610-108, April 2009
This signal is not used by the CF Card, and is pulled up to
VCC through a 4.7K ohm resistor.
In all modes, when Ultra DMA mode DMA Write is active, this
signal is asserted by the device during a data burst to
indicate that the device is ready to receive Ultra DMA data
out bursts. The device may negate -DDMARDY to pause an
Ultra DMA transfer.
In all modes, when Ultra DMA mode DMA Read is active, this
signal is the data in strobe generated by the device. Both the
rising and falling edge of DSTROBE cause data to be latched
by the host. The device may stop generating DSTROBE
edges to pause an Ultra DMA data in burst
This signal is not used by the CF Card, and is pulled up to
VCC through a 4.7K ohm resistor.
Same as –DDMARDY above.
Same as DSTROBE above.
This signal is not used by the CF Card, and is pulled up to
VCC through a 4.7K ohm resistor.
Same as –DDMARDY above.
Same as DSTROBE above.
Ground
Ground
Ground
+5 V or 3.3V power
+5 V or 3.3V power
+5 V or 3.3V power
When RESET is high, this signal resets the CF Card. The CF
Card is reset only at power up if this signal is left high or
open from power-up. The CF Card can also be reset when
the soft reset bit in the Configuration Option Register is set.
This signal is the same as the PC Card Memory Mode signal.
In the True IDE Mode this input pin is the active low hardware
reset from the host.
-VS1 is grounded, so that the card CIS can be read 3.3 volts.
-VS2 is reserved for a secondary voltage and is not
connected.
CompactFlash Card
11