SLCF064JIU STEC, SLCF064JIU Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
SLCF064JIU
Manufacturer Part Number
SLCF064JIU
Description
Manufacturer
STEC
Type
CompactFlashr
Datasheet
1.SLCF064JIU.pdf
(43 pages)
Specifications of SLCF064JIU
Density
64MByte
Operating Supply Voltage (typ)
3.3/5V
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Package Type
Not Required
Mounting
Socket
Pin Count
50
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
3.18/4.75V
Operating Supply Voltage (max)
3.465/5.25V
Programmable
Yes
Lead Free Status / Rohs Status
Compliant
SimpleTech P/N:
(where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device)
SIGNAL DESCRIPTIONS
-OE
(PC Card Memory Mode)
-OE
(PC Card I/O Mode)
-OE
(True IDE Mode)
RDY/-BSY
(PC Card Memory Mode)
-IREQ
(PC Card I/O Mode)
INTRQ
(True IDE Mode)
A10-A0
(PC Card Memory Mode)
A10-A0
(PC Card I/O Mode)
A2-A0
(True IDE Mode)
-CE1, -CE2
(PC Card Memory Mode)
Card Enable
-CE1, -CE2
(PC Card I/O Mode)
Card Enable
-CS0, -CS1
(True IDE Mode)
Signal Name
SLCF064J(U)(I)-(F)
Dir
O
I
I
I
14, 15, 16, 17,
8, 10, 11, 12,
18, 19, 20
27, 28, 29
7, 32
Pin
37
9
(continued)
This is an Output Enable strobe generated by the host interface. It is used
to read data from the card in Memory Mode and to read the CIS and
configuration registers.
In PC Card I/O Mode, this signal is used to read the CIS and configuration
registers.
To enable True IDE Mode, this input should be grounded by the host.
In Memory Mode this signal is set high when the card is ready to
accept a new data transfer operation and held low when the card is
busy. The host memory card socket must provide a pull-up resistor. At
power up and at reset, the RDY/-BSY signal is held low (busy) until
the card has completed its power up or reset function. No access of
any type should be made to the card during this time. The RDY/-BSY
signal is held high (disabled from being busy) whenever the following
condition is true: the card has been powered up with RESET
continuously disconnected or asserted high.
After the card has been configured for I/O operation, this signal is used as
the active low interrupt request. This line is strobed low to generate a pulse
mode interrupt or held low for a level mode interrupt.
In True IDE Mode, this signal is the active high interrupt request to the
host.
These address lines along with the -REG signal are used to select the
following: the I/O port address registers within the card, the memory
mapped port address registers within the card, a byte in the card’s
information structure and the card’s configuration control and status
registers.
This signal is the same as the PC Card Memory Mode signal.
In True IDE Mode only, A2:A0 are used to select the one of eight registers
in the Task File. The remaining address lines should be grounded.
These input signals are used both to select the card and to indicate to the
card whether a byte or a word operation is being performed. -CE2 always
accesses the odd byte of the word. -CE1 accesses the even byte or the odd
byte of the word depending on A0 and -CE2. A multiplexing scheme based
on A0, -CE1, -CE2 allows 8 bit hosts to access all data on D0-D7.
This signal is the same as the PC Card Memory Mode signal.
In the True IDE Mode, -CS0 is the chip select for the task file registers while
-CS2 is used to select the Alternate Status Register and the Device Control
Register.
Document Part Number 61000-02805-310 July 2005
Description
COMPACTFLASH
(continued)
Page 7