CAT5241Y-10 ON Semiconductor, CAT5241Y-10 Datasheet - Page 4

• Manufacturer Part Number: CAT5241Y-10
• Manufacturer: ON Semiconductor

Specifications of CAT5241Y-10

• Number Of Elements: 4
• # Of Taps: 64
• Resistance (max): 10KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (2-Wire/I2C)
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.5V
• Single Supply Voltage (max): 6V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 20
• Lead Free Status / Rohs Status: Compliant

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The minimum DC input voltage is −0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC
2. Latch−up protection is provided for stresses up to 100 mA on address and data pins from –1 V to V
3. This parameter is tested initially and after a design or process change that affects the parameter.
4. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a
5. Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer.
6. LSB = R
7. n = 0, 1, 2, ..., 63
Table 2. ABSOLUTE MAXIMUM RATINGS
Table 3. RECOMMENDED OPERATING CONDITIONS
Table 4. POTENTIOMETER CHARACTERISTICS
Temperature Under Bias
Storage Temperature Range
Voltage on any Pin with Respect to V
V
Package Power Dissipation Capability (T
Lead Soldering Temperature (10 s)
Wiper Current
V
Operating Ambient Temperature (Industrial)
C
TC
voltage on output pins is V
Symbol
TC
potentiometer.
It is a measure of the error in step size.
CC
CC
H
V
R
R
R
R
/C
TERM
R
R
V
I
RATIO
POT
POT
POT
POT
RPOT
fc
W
with Respect to Ground
W
W
N
L
/C
W
TOT
/ 63 or (R
Potentiometer Resistance (−00)
Potentiometer Resistance (−50)
Potentiometer Resistance (−10)
Potentiometer Resistance (−25)
Potentiometer Resistance Tolerance
R
Power Rating
Wiper Current
Wiper Resistance
Wiper Resistance
Voltage on any R
Noise
Resolution
Absolute Linearity (Note 4)
Relative Linearity (Note 5)
Temperature Coefficient of R
Ratiometric Temp. Coefficient
Potentiometer Capacitances
Frequency Response
POT
Matching
H
− R
CC
Parameter
L
) / 63, single pot
+ 0.5 V, which may overshoot to V
H
or R
SS
Parameter
Parameter
L
Pin
(Notes 1, 2)
A
= 25°C)
POT
http://onsemi.com
(Over recommended operating conditions unless otherwise stated.)
R
I
I
W
W
R
W(n)(actual)
R
POT
= ±3 mA @ V
= ±3 mA @ V
Test Conditions
W(n+1)
25°C, each pot
CC
= 50 kW (Note 3)
V
4
(Note 3)
(Note 7)
(Note 7)
(Note 3)
(Note 3)
(Note 3)
SS
+ 2.0 V for periods of less than 20 ns.
−[R
−R
= 0 V
W(n)+LSB
(n)(expected)
CC
CC
= 3 V
= 5 V
]
GND
Min
−2.0 to +V
−55 to +125
−65 to +150
−2.0 to +7.0
+2.5 to +6.0
−40 to +85
CC
Ratings
Ratings
10/10/25
300
±12
±300
TBD
1.0
+ 1 V.
Typ
100
2.5
1.6
0.4
50
10
80
CC
+2.0
Max
±0.2
V
±20
300
150
50
±6
±1
20
1
CC
Units
Units
(Note 6)
(Note 6)
nV/√Hz
ppm/°C
ppm/°C
mA
Units
°C
°C
°C
°C
W
MHz
V
V
V
LSB
LSB
mW
mA
kW
kW
kW
kW
pF
%
%
%
W
W