AD7569KP-REEL Analog Devices Inc, AD7569KP-REEL Datasheet - Page 14

• Manufacturer Part Number: AD7569KP-REEL
• Manufacturer: Analog Devices Inc

Specifications of AD7569KP-REEL

• Converter Type: ADC/DAC
• Resolution: 8b
• Number Of Dac's: Single
• Data Rate: 0.5MSPS
• Digital Interface Type: Parallel
• Pin Count: 28
• Package Type: PLCC
• Lead Free Status / Rohs Status: Not Compliant

AD7569/AD7669
INTERFACING THE AD7569/AD7669
AD7569/AD7669—Z80 INTERFACE
Figure 17 shows a typical interface to the Z80 microprocessor.
The ADC is configured for operation in the Mode 1 interface
mode. A precise timer or clock source starts conversion in appli-
cations requiring equidistant sampling intervals. The scheme
used, whereby INT of the AD7569/AD7669 generates an inter-
rupt on the Z80, is limited in that it does not allow the ADC to
be sampled at the maximum rate. This is because the time be-
tween samples has to be long enough to allow the Z80 to service
its interrupt and read data from the ADC. To overcome this,
some buffer memory or FIFO could be placed between the
AD7569/AD7669 and the Z80. Writing data to the relevant
AD7569/AD7669 DAC simply consists of a <LD (nn), A> in-
struction where nn is the decoded address for that DAC. Read-
ing data from the ADC, after an INT has been received,
consists of a < LDA, (nn)> instruction.
AD7569/AD7669—68008 INTERFACE
A typical interface to the 68008 is shown in Figure 18. In this
case, the ADC is configured in the Mode 2 interface mode. This
means that the one read instruction starts conversion and reads
the data. The read cycle is stretched out over the entire conver-
sion period by taking the INT line back into the DTACK input
of the 68008. The additional gates are required so the 68008
receives a DTACK when the processor is writing data to the
AD7569/AD7669. In this case, there are no wait states intro-
duced into the write cycle. Writing data to the relevant AD7569/
AD7669 DAC consists of a <MOVE.B Dn, addr> where Dn is
the data register, which contains the data to be loaded to that
DAC, and addr is the decoded address for the DAC. Data is
read from the ADC using a <MOVE.B addr,Dn> with the con-
version result placed in register Dn.
Figure 18. AD7569/AD7669 to 68008 Interface
Figure 17. AD7569/AD7669 to Z80 Interface
–14–
AD7569/AD7669—ADSP-2100 INTERFACE
Figure 19 shows a typical interface to the DSP processor, the
ADSP-2100. The ADC is in the Mode 2 interface mode, which
means that the ADSP-2100 is halted during conversion. This is
achieved using the decoded address output. This is gated with
DMWR to ensure that it halts the processor for READ instruc-
tions only. INT going low at the end of conversion releases the
processor and allows it to finish off the READ instruction.
Because the instruction cycle of the ADSP-2100 is so fast
(125 ns cycle), the DMWR pulse also has to be stretched also
for write cycles. This is achieved using the 74121, which gener-
ates a pulse that is fed back to DMACK. The duration of this
pulse determines how long the ADSP-2100 write cycle is
stretched. The buffers driving the DMACK line must have
open-collector outputs. Writing data to the relevant AD7569/
AD7669 DAC is achieved using a single instruction, <DM
(addr) = MRO>, where addr is the decoded address of that
DAC, and MRO contains the data to be loaded to the DAC reg-
ister. Data is read from the ADC also, using a single instruction
<MRO = DM (addr)>, where the conversion result is placed in
the MRO data register.
AD7569/AD7669—IBM PC* INTERFACE
The AD7569/AD7669 is ideal for implementing an analog in-
put/output port for the IBM PC. Figure 20 shows an interface
that realizes this function. The ADC is configured in the Mode
1 interface mode, and conversions are initiated using a precise
clock source for equidistant sampling intervals. At the end of
conversion, the INT line goes low, and the 74121 generates
*IBM PC is a trademark of International Business Machines Corp.
Figure 19. AD7569/AD7669 to ADSP-2100 Interface
Figure 20. AD7569/AD7669 to IBM PC Interface
REV. B