SLATAFL064JU STEC, SLATAFL064JU Datasheet

Page 1

MB ATA Flash PC Card FEATURES • ATA-4 Compatibility • Support for PCMCIA I/O, Memory and True-IDE Interfaces • Form Factors: PC Card Type II • Endurance Guarantee of 2,000,000 Write/Erase Cycles • CIS (Card Information Structure) Programmed into ...

Page 2

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) PACKAGE DIMENSIONS AND PIN LOCATIONS PC Card Type II Length ...................................... 3.370±0.008 in (85.60±0.20 mm) Width ........................................ 2.126±0.004 in (54.00±0.10 mm) Thickness .................................... 0.196 in max. (5.00 mm ...

Page 3

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) PIN ASSIGNMENTS PC Card Memory Mode Pin Signal Num Name 1 GND 2 D03 3 D04 4 D05 5 D06 6 D07 7 -CE1 8 A10 9 -OE ...

Page 4

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) PIN ASSIGNMENTS (continued) PC Card Memory Mode Pin Signal Num Name 51 VCC ...

Page 5

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) SIGNAL DESCRIPTIONS Signal Name Dir BVD2 (PC Card Memory Mode) -SPKR (PC Card I/O Mode) -DASP (True IDE Mode) -CD1, -CD2 O 36, 67 (PC ...

Page 6

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) SIGNAL DESCRIPTIONS Signal Name Dir -OE I (PC Card Memory Mode) -OE (PC Card I/O Mode) -OE (True IDE Mode) RDY/-BSY O (PC Card Memory Mode) -IREQ (PC ...

Page 7

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) SIGNAL DESCRIPTIONS Signal Name Dir -CSEL I (PC Card Memory Mode) -CSEL (PC Card I/O Mode) -CSEL (True IDE Mode) -REG I (PC Card Memory Mode) Attribute Memory ...

Page 8

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) SIGNAL DESCRIPTIONS Signal Name Dir -WAIT O (PC Card Memory Mode) -WAIT (PC Card I/O Mode) IORDY (True IDE Mode) GND — 1, 34, 35, 68 (PC Card ...

Page 9

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin w.r.t. Vss Storage Temperature range RECOMMENDED OPERATING CONDITIONS Parameter Commercial operating temperature Industrial operating temperature VCC voltage PERFORMANCE Item Data ...

Page 10

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) ENVIRONMENTAL CHARACTERISTICS Leaded Cards (without the “U” option) Shock half-sine, 0.330 ms to 0.750 ms (per MIL-STD-202G Method 213B, Condition A) Vibration 10Hz-2KHz (per ...

Page 11

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) AC CHARACTERISTICS (Ta = 0°C to 70°C for commercial temperature parts –40°C to 85°C for industrial temperature parts; VCC = 5V±5% or VCC = 3.3V +5% ...

Page 12

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) AC CHARACTERISTICS Attribute Memory Write AC Characteristics Speed Version: Item Write Cycle Time Write Pulse Width Address Setup Time Data Setup Time for -WE Data Hold Time Write ...

Page 13

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) AC CHARACTERISTICS I/O Access Read AC Characteristics Cycle Time Mode: Item Data Delay after -IORD Data Hold following -IORD -IORD Width Time Address Setup before -IORD Address Hold ...

Page 14

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) AC CHARACTERISTICS I/O Access Write AC Characteristics Cycle Time Mode: Item Data Setup before -IOWR Data Hold following -IOWR -IOWR Width Time Address Setup before -IOWR Address Hold ...

Page 15

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) AC CHARACTERISTICS Register Access AC Characteristics for True IDE Parameter Cycle time (min) Address valid to -IORD/-IOWR (min) setup -IORD/-IOWR pulse width 8bit (min) -IORD/-IOWR recovery time (min) ...

Page 16

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) AC CHARACTERISTICS True IDE Mode Access Read/Write Timings ADDR valid -IORD/-IOWR D15 to D0 (Write) D15 to D0 (Read) -IOIS16 IORDY (continued ...

Page 17

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) HOST ACCESS SPECIFICATION Attribute Access Specifications The CIS can be accessed by Byte/Word/Odd-byte modes which are defined by PC Card card standard specifications. The -REG signal must be ...

Page 18

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Task File Register Access Specifications There are two cases of Task File register mapping, one is the mapped I/O address area, the other is mapped Memory address area. ...

Page 19

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Memory Address Map Task File Register Read Access Mode Mode -REG -CE2 Standby Mode x H Byte Access (8 bit Word Access (16-bit) H ...

Page 20

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) True IDE Mode The card is configured in a True IDE mode of operation when the -OE input signal is asserted GND by the host at power up. ...

Page 21

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) CIS INFORMATION (TYPICAL) -------- 0000: Code 01, link -------- Tuple CISTPL_DEVICE (01), length 3 (03) at offset 0 Device type is FUNCSPEC Device speed ...

Page 22

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) -------- 0037: Code 1A, link -------- Tuple CISTPL_CONFIG (1A), length 5 (05) at offset 37 Last valid configuration index is 3 Configuration ...

Page 23

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) 0064: Code 1B, link -------- Tuple CISTPL_CFTABLE_ENTRY (1B), length 15 (0F) at ...

Page 24

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) CONFIGURATION REGISTER SPECIFICATION This card supports four configuration registers for the purpose of the configuration and observation of the card. These registers can be used in memory card ...

Page 25

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Configuration and Status Register (Address 202h) This register is used for observing the card state. bit7 bit6 bit5 CHGED SIGCHG IOIS8 Initial Value: 00h Name R/W Function CHGED ...

Page 26

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Pin Replacement Register (Address 204h) This register is used for providing the signal state of -IREQ when the card is configured as the I/O card interface. bit7 bit6 ...

Page 27

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) TASK FILE REGISTER SPECIFICATION These registers are used for reading and writing data to the card. These registers are mapped four types by the configuration of INDEX in ...

Page 28

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Contiguous I/O Map (INDEX=1) -REG A10- ...

Page 29

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Secondary I/O Map (INDEX=3) -REG A10 A9- 17h 0 X 17h 0 X 17h 0 X 17h 0 X 17h 0 X 17h 0 X 17h ...

Page 30

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Data Register The Data Register bit read/write register used for transferring data between the card and the host. This register can be accessed in word ...

Page 31

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Sector Count Register This register contains the numbers of sectors of data requested to be transferred on a read or write operation between the host and the card. ...

Page 32

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Drive/Head Register This register select the device address translation (CHS or LBA) and provides head address (CHS) or high order address bits 27:24 for LBA. bit7 bit6 bit5 ...

Page 33

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Status Register This read only register indicates status of a command execution. When the BSY bit is “0”, the other bits are valid; when the BSY bit is ...

Page 34

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Device Control Register This write only register is used for controlling the interrupt request and issuing an ATA soft reset to the card. bit7 bit6 bit5 bit4 x ...

Page 35

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) ATA COMMAND SPECIFICATIONS This table with the following paragraphs summarizes the ATA command set. No. Command set 1 Check Power Mode 2 Execute Drive Diagnostic 3 Erase Sector(s) ...

Page 36

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Check Power Mode (code: E5h or 98h) This command checks the power mode. Execute Drive Diagnostic (code: 90h) This command performs the internal diagnostic tests implemented by the ...

Page 37

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Word Data Total Address Bytes 0 848AH 2 General configuration bit-significant information (value=044AH for versions with the -F suffix) 1 XXXXH 2 Default number of cylinders 2 0000H ...

Page 38

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Request Sense (code: 03h) This command requests an extended error code after a command ends with an error. Refer to table below. Code Description 00H No error detected ...

Page 39

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Write Multiple (code: C5h) This command is similar to the Write Sectors command. Interrupts are not presented on each sector, but on the transfer of a block which ...

Page 40

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) SECTOR TRANSFER PROTOCOL Sector Read One sector read procedure after the card is configured to I/O interface is shown in the following charts. Set the cylinder low/high register ...

Page 41

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) Sector Write One sector write procedure after the card is configured to I/O interface is shown in the following charts. Set the cylinder low/high register Set the head ...

Page 42

SLATAFL064J(U)(I)-(F) SimpleTech P/N: (where U=RoHS compliant lead-free; I=Ind. Op. Temp; F=fixed device) REVISION HISTORY Rev. Change Description from Previous Revision -301 5/26/04. Initial Release. -302 7/1/04. Sleep mode current at 3.3V corrected to 80µA from 80mA. The operating current at ...