LQ104S1DG31 Sharp Electronics, LQ104S1DG31 Datasheet
![no-image](/images/manufacturer_photos/0/6/602/sharp_electronics_sml.jpg)
LQ104S1DG31
Specifications of LQ104S1DG31
Related parts for LQ104S1DG31
LQ104S1DG31 Summary of contents
Page 1
... Technical Document LCD Specification LCD Group LQ104S1DG31 LCD Module Product Specification August 2006 SVGA LCD Module featuring digital interface, 350 nits brightness with 500:1 contrast. Full Specifications Listing. ...
Page 2
...
Page 3
... LQ104S1DG31 SPEC No. DATE LD-18815A AUG.25.2006 LD-18815B DEC.22.2006 LD-18815C JUL.01.2008 RECORDS OF REVISION SUMMARY PAGE - 1 Corrected “Confirm "11.… → Confirm "12. …“ 3 Corrected “【Note2】…described in 7-2.→8-2.“ Added the sentence 6 【 Note5 】 Lamp life time shortens according to the state of mounting and use. Added “ ...
Page 4
... Application This specification applies to color TFT-LCD module, LQ104S1DG31 These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 5
Outline specification. Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1: excluding backlight cables. Outline dimensions is shown in Fig.1 4. Input Terminals 4-1. TFT-LCD panel driving ...
Page 6
Pin No. Symbol 1 GND 2 CK Clock signal for sampling each data signal 3 GND 4 Hsync Horizontal synchronous signal 5 Vsync Vertical synchronous signal 6 GND 7 GND 8 GND 9 R0 RED data signal(LSB) RED ...
Page 7
SCAN = High 4-3. Backlight driving CN2 ,CN3 Used connector : BHR-02(8.0)VS-1N (JST) Corresponding connector : SM02(8.0)B-BHS-1-TB(LF)(SN) or -1N-TB(LF) or -1R-TB(LF) (JST) Pin no. symbol 1 VHIGH Power supply for lamp (High voltage side) 2 VLOW Power supply ...
Page 8
TFT-LCDpaneldriving Parameter Power Supply voltage Supply Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (low) Input current (High) [Note1]On-off conditions for supply voltage 0<t1≦15ms 0<t2≦10ms 0<t3≦100ms 0<t4≦1s 200ms<t5 Vcc-dip conditions 1) 2.5V≦Vcc td≦10ms ...
Page 9
Backlight driving The backlight system is an edge-lighting type with double CCFT (Cold Cathode Fluorescent Tube). The characteristics of single lamp are shown in the following table. (It is usually required to measure under the following condition. IL=6.0mA,Ta=25℃±2℃,FL=60kHz.) Parameter ...
Page 10
Timing Characteristics of input signals Timing diagrams of input signal are shown in Fig.2. 8-1. Timing characteristics Parameter Clock Frequency High time Low time Duty ratio Data Setup time Hold time Horizontal Cycle sync. signal Pulse width Vertical Cycle ...
Page 11
THp (Hsync) THc * Only when enable terminal is fixed “LOW” ...
Page 12
Data signal Vertical invalid data period (R0∼R5,G0∼G5, B0∼B5) Data Enable signal (ENAB) Horizontal display position Clock signal (CK) Data signal Horizontal invalid period (R0∼R5,G0∼G5, B0∼B5) Data Enable signal (ENAB) TVd DH1 DH2 DH3 DH599 Tch Tcl Th ...
Page 13
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale Gray Scale Black 0 0 − ...
Page 14
Optical Characteristics Parameter Viewing Horizontal θ21, θ22 angle Vertical range Contrast ratio Response Rise time Decay Chromaticity of white Luminance of white White Uniformity [Note] The measurement shall be executed 30 minutes after lighting at rating. (condition:IL=6.0mA rms) The ...
Page 15
Definitions of viewing angle range: [Note2] Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) = [Note3] Definition of response time: The response time is defined as the following figure and shall be ...
Page 16
Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. ...
Page 17
... Fig.4 2 once for each direction. 15-2 Packing box Label: (4S)LQ104S1DG31 社内品番: Barcode (1T)2006.09.01 LotNO. : ...
Page 18
Carton storage condition Temperature 0℃ to 40℃ Humidity 95%RH or less Reference condition : 20℃ to 35℃ , 85%RH or less (summer) : 5℃ to 15℃ , 85%RH or less (winter) ・the total storage time (40℃,95%RH) : 240H or ...
Page 19
... Fig.1 OUTLINE DIMENSIONS ( LQ104S1DG31 ) LD18815C-16 ...
Page 20
LD18815C-17 Fig.4 PACKING FORM ...
Page 21
... MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable, or responsible in any way, for any incidental or consequential economic or property damage. LD-18815C EUROPE Sharp Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE Sharp Electronics (Singapore) PTE ...