TSOP58336 Vishay, TSOP58336 Datasheet

no-image

TSOP58336

Manufacturer Part Number
TSOP58336
Description
Manufacturer
Vishay
Datasheet

Specifications of TSOP58336

Lead Free Status / Rohs Status
Compliant
MECHANICAL DATA
Pinning for TSOP581.., TSOP583..:
1 = OUT, 2 = GND, 3 = V
Pinning for TSOP591.., TSOP593..:
1 = OUT, 2 = V
BLOCK DIAGRAM
Document Number: 81398
Rev. 1.6, 22-Nov-10
PARTS TABLE
CARRIER
FREQUENCY
30 kHz
33 kHz
36 kHz
38 kHz
40 kHz
56 kHz
16833_14
PIN
Input
S
IR Receiver Modules for Remote Control Systems
, 3 = GND
AGC
1 = OUT, 2 = GND, 3 = V
Control circuit
S
Band
pass
TSOP58130
TSOP58133
TSOP58136
TSOP58138
TSOP58140
TSOP58156
SHORT BURST AND HIGH DATA RATE
Demo-
dulator
19026
33 kΩ
TSOP581.., TSOP583.., TSOP591.., TSOP593..
(AGC1)
S
1 = OUT, 2 = V
3
1
2
TSOP59130
TSOP59133
TSOP59136
TSOP59138
TSOP59140
TSOP59156
S
, 3 = GND
FEATURES
• Low supply current
• Photo detector and preamplifier in one
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.7 V to 5.5 V
• Suitable for short bursts: burst length ≥ 6
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Compliant to RoHS Directive 2002/95/EC and in
DESCRIPTION
These products are miniaturized receiversfor infrared
remote control systems. A PIN diode and a preamplifier are
assembled on a lead frame, the epoxy package acts as an
IR filter.
The demodulated output signal can directly be decoded by
a microprocessor. The main benefit of the TSOP581..,
TSOP591.. is the compatibility to all IR remote control data
formats. The TSOP583.., TSOP593 are optimized to better
suppress spurious pulses from fluorescent lamps, LCD TVs
or plasma displays.
This component has not been qualified according to
automotive specifications.
APPLICATION CIRCUIT
PINNING
package
carrier cycles
accordance to WEEE 2002/96/EC
17170_7
The external components R
to improve the robustness against electrical overstress
(typical values are R
The output voltage V
below 1 V by the external circuit.
The capacitive load at the output should be less than 2 nF.
Transmitter
TSALxxxx
with
1 = OUT, 2 = GND, 3 = V
NOISY ENVIRONMENTS AND SHORT BURSTS
TSOP58330
TSOP58333
TSOP58336
TSOP58338
TSOP58340
TSOP58356
IR receiver
1
O
= 100 Ω, C
should not be pulled down to a level
Vishay Semiconductors
1
and C
GND
V
OUT
1
S
= 0.1 µF).
(AGC3)
1
S
are optional
1 = OUT, 2 = V
C
R
1
1
V
O
TSOP59330
TSOP59333
TSOP59336
TSOP59338
TSOP59340
TSOP59356
µC
www.vishay.com
GND
+ V
S
, 3 = GND
S
1

Related parts for TSOP58336

TSOP58336 Summary of contents

Page 1

... R The output voltage V below the external circuit. The capacitive load at the output should be less than 2 nF. Vishay Semiconductors NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3 OUT TSOP58330 TSOP59330 TSOP58333 TSOP59333 TSOP58336 TSOP59336 TSOP58338 TSOP59338 TSOP58340 TSOP59340 TSOP58356 TSOP59356 receiver ...

Page 2

... TSOP581.., TSOP583.., TSOP591.., TSOP593.. Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER Supply voltage Supply current Output voltage Voltage at output to supply Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied ...

Page 3

... off 21394 Fig Sensitivity vs. Supply Voltage Disturbances 1.3 20747 Fig Sensitivity vs. Electric Field Disturbances Vishay Semiconductors 5.0 Correlation with Ambient Light Sources: 4 W/m = 1.4 kLx (Std. illum 2855 W/m = 8.2 kLx (Daylight 5900 K) 4.0 3.5 3.0 2.5 2.0 Wavelength of Ambient 1.5 Illumination: λ ...

Page 4

... TSOP581.., TSOP583.., TSOP591.., TSOP593.. Vishay Semiconductors 1.0 0.9 0.8 0.7 0.6 0.5 0.4 TSOP583.. 0.3 TSOP593.. 0.2 0 mW/m² 21590-9 Burst Length (Number of Cycles/Burst) Fig Max. Envelope Duty Cycle vs. Burst Length 0.45 0.4 0.35 0.3 0.25 0.2 0. Ambient Temperature (°C) 21397 amb Fig ...

Page 5

... Common disturbance signals are supressed (e.g. waveform of figure 15) Vishay Semiconductors IR Signal from Fluorescent Lamp with Low Modulation Time (ms) Fig Signal from Fluorescent Lamp with Low Modulation IR Signal from Fluorescent ...

Page 6

... TSOP581.., TSOP583.., TSOP591.., TSOP593.. Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 2.54 nom. Drawing-No.: 6.550-5263.01-4 Issue: 12; 16.04.10 19009 www.vishay.com 6 IR Receiver Modules for Remote Control Systems 5 (4) (1.54) 0.85 max. 0.7 max. 2.54 nom. Marking area R 2 4.8 2 0.5 max. 1.2 ± 0.2 ...

Page 7

... Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’ ...

Related keywords