5962-9160901MLA E2V, 5962-9160901MLA Datasheet - Page 16

• Manufacturer Part Number: 5962-9160901MLA
• Manufacturer: E2V

Specifications of 5962-9160901MLA

• Logic Family: ACT
• Logical Function: Diagnostic Register
• Number Of Elements: 1
• Number Of Bits: 8
• Number Of Inputs: 9
• Number Of Outputs: 9
• Propagation Delay Time: 15.5ns
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Output Type: 3-State
• Clock-edge Trigger Type: Positive-Edge
• Polarity: Non-Inverting
• Technology: CMOS
• Mounting: Through Hole
• Pin Count: 24
• Operating Temp Range: -55C to 125C
• Operating Temperature Classification: Military
• Quiescent Current: 160uA
• Lead Free Status / Rohs Status: Not Compliant

DSCC FORM 2234
APR 97
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
4.4.1 Group A inspection.
a.
b.
c.
a.
b.
c.
d.
DEFENSE SUPPLY CENTER COLUMBUS
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of
T
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
Subgroup 4 (C
design changes which may affect capacitance. Test all applicable pins on 5 devices with zero failures.
MIL-STD-883.
Tests shall be as specified in table II herein.
For device class M, subgroups 7 and 8 tests shall be sufficient to verify the truth table as specified on figure 2 herein.
For device classes Q and V, subgroups 7 and 8 shall include verifying the functionality of the device.
A
= +125°C, minimum.
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
1/ PDA applies to subgroup 1.
2/ PDA applies to subgroups 1 and 7.
Interim electrical
Final electrical
Group A test
Group C end-point electrical
Group D end-point electrical
Group E end-point electrical
parameters (see 4.2)
parameters (see 4.2)
requirements (see 4.4)
parameters (see 4.4)
parameters (see 4.4)
parameters (see 4.4)
Test requirements
STANDARD
IN
, C
OUT
, C
IN/OUT
, and C
TABLE II. Electrical test requirements.
PD
measurements) shall be measured only for the initial test and after process or
1, 2, 3, 7, 8, 9,
10, 11 1/
1, 2, 3, 4, 7, 8, 9,
10, 11
method 5005, table I)
(in accordance with
MIL-STD-883,
Subgroups
class M
Device
1, 2, 3
1, 2, 3
1, 7, 9
---
SIZE
A
1, 2, 3, 7, 8, 9,
10, 11 1/
1, 2, 3, 4, 7, 8,
9, 10, 11
class Q
Device
1, 2, 3
1, 2, 3
1, 7, 9
MIL-PRF-38535, table III)
1
(in accordance with
REVISION LEVEL
Subgroups
1, 2, 3, 7, 8, 9,
10, 11 2/
1, 2, 3, 4, 7, 8,
9, 10, 11
A
class V
Device
1, 2, 3
1, 2, 3
1, 7, 9
1
SHEET
5962-91609
16