K-D1A Leach International, K-D1A Datasheet
![no-image](/images/no-image-200.jpg)
K-D1A
Specifications of K-D1A
Related parts for K-D1A
K-D1A Summary of contents
Page 1
... N/A N/A EUROPE ASIA 2 Rue Goethe Units 602-603 6/F Lakeside 1 57430 Sarralbe No.8 Science Park West Avenue France Phase Two, Hong Kong Science Park . Pak Shek Kok, Tai Po, N.T. . Hong Kong Tel: (33 Tel: (852) 2 191 3830 Fax: (33 Fax: (852) 2 389 5803 ...
Page 2
... Test condition - G and J mounting - Duration Shock (A, D and W mounting) Shock (G and J mounting) Maximum contact opening time under vibration and shock Operate time at nominal voltage@25°C Release time at nominal voltage@25°C Contact make bounce at nominal voltage@25°C Contact release break bounce at nominal voltage@25°C Weight maximum Unless otherwise noted, the specified temperature range applies to all relay characteristics ...
Page 3
... Standard Intermediate current test applicable. [ load life, 10,000 cycles. [3] Inductive load life, 20,000 cycles. [4] "N, R & V" coils have back EMF suppression volts maximum. [5] 500 Vrms with silicone gasket compressed, 350 Vrms all other conditions. [6] Applicable to Type "N, R & V" coils only. ...
Page 4
... TERMINAL TYPE 2 WIRING DIAGRAM STANDARD TOLERANCE: .XX =.03; .XXX =.010 - 128 - FINISH: CASE-TIN/LEAD PINS-GOLD PLATE SILICONE RUBBER GASKET .050 .270 + .005 - + .062 .001 - DIA PIN 14 PLACES TERMINAL TYPE 4 STANDARD TERMINAL LAYOUT -X2 D .200 C B +X1 A .200 .400 .600 SERIES K .400 .600 Page ...
Page 5
... This method is valid only for Resistive Loads, and is an approximation only; keeping in mind the limitations mentioned above. Example: A designer is working with a 55 volt DC system and has a relay rated at 10 amps resistive at 28 volts DC. What is the maximum current that can be switched at 55 Vdc. ...
Page 6
... Most relay parameters are specified as maximum values over the rated temperature range of the specific relay. Users often find that key parameters differ significantly at ambient temperature (20-25°C) and sometimes fall into the trap of specifying their system around these ambient parameters. Additionally the actual temperature experienced by the relay can be far in excess of existing ambient temperatures due to the heat generated by the coil current and the contact load ...
Page 7
... Calculation of coil temperature rise when R initial and R final are known: Delta T = (234 Delta T = Temperature rise (° Initial temperature (° Initial resistance (Ohms Final resistance (Ohms Temperature can also be found by making the R coefficient of correction graph in Fig. 2, and then finding the corresponding temperature. ...
Page 8
Application notes CURVES FOR DC VOLTAGES ABOVE NORMAL RATING: RESISTIVE LOAD ONLY Date of issue: 6/00 (without arc suppression N°103D Page ...
Page 9
... The faster the switch-off, the higher the induced voltage. All coil suppression networks are based on a reduction of speed of current decay. This reduction may also slow down the opening of contacts, adversly effecting contact life and reliability. Therefore very important to have a clear understanding of these phenomena when designing a coil suppression circuitry ...
Page 10
... R = coil resistance in kiloOhms C = capacitance in microFarads The series resistor must be between 0.5 and 1 times the coil resistance. Special consideration must be taken for the capacitor inrush current in the case of a low resistance coil. The record shown opposite is performed on the same relay as above. The operation time becomes: - time to start the movement 2 ...
Page 11
... At the opening time the current becomes constant as a result of practically zero opening speed. Due to this kind of behavior, this type of suppression must be avoided for power relays. For small relays which have to switch low currents of less than 0.2 A, degradation of life is not that significant and the method may be acceptable. ...
Page 12
... The lower curve on the opposite record demonstrates those characteristics. Voltage limitation occurs at 42V. The two voltages spikes generated by internal movement are at lower levels than zener conduction result, no current is recycled in the coil. The opening time phases are as follows: - time to start the movement 2 ...
Page 13
... Or when mounted in the same direction, separate each relay from the other by 1/8 inch (figure “B”). If two or more rows of relays are installed, allow clearance of 1/8 inch between rows, (figures “ ...
Page 14
... Tel: (01) 714-736-7599 Tel: (33 Fax: (01) 714-670-1145 Fax: (33 RELAY SOCKET 12 AMP ASIA Units 602-603 6/F Lakeside 1 No.8 Science Park West Avenue Phase Two, Hong Kong Science Park Pak Shek Kok, Tai Po, N.T. Hong Kong Tel: (852) 2 191 3830 Fax: (852) 2 389 5803 Page ...
Page 15
... Dielectric withstanding voltage Weight Temperature range Vibration Shock This socket is designed to snap and lock into a panel to reduce hardware requirement and mounting time. Contacts and hardware are provided disassembled in a plastic bag. Standard tolerances are .xx=±.01; .xxx= ±.005 unless otherwise noted. © Featuring ...
Page 16
... SOCKET DIMENSIONS RELAY GASKET SUPPLIED WITH RELAY .20 TERMINAL LAYOUT SO-SSL-JA-2 Date of issue: 3/06 MTG SCREW PHILLIPS HEAD WASHER SPACER PANEL .064±.005 THICK SOCKET RECOMMENDED MOUNTING PANEL CUTOUT WIRE SEALING GROMMET .20 .520 MAX .10 1.40 SO-SSL-JA SO-SSL (2 POLE) 1.40 1.16 .55 4X R.055 MAX 2X Ø ...
Page 17
... RELAY .200 TYP .62 TERMINAL LAYOUT SO-SSL-K-1 SO-SSL-KL-1 Date of issue: 3/06 RELAY MTG SCREW PHILLIPS HEAD WASHER SPACER .62 PANEL .064±.005 THICK SOCKET WIRE SEALING GROMMET RECOMMENDED MOUNTING PANEL CUTOUT .10 .200 TYP 1.000 MAX 1.40 SO-SSL-KA SO-SSL (4 POLE) 1.40 1.16 1.110 MIN 4X R.055 MAX 3X Ø ...
Page 18
... SOCKET NUMBERING SYSTEM 1-Basic socket designation________________________| 2-Body style (short snap lock)________________________| 3-Mating relay (J, JA, K, KA, KL, TDX)____________________| 4-Polarization (see terminal layout)__________________________||| 5-Hardware (0=less hardware, 1=with hardware)__________________|| 6-Contacts (0=less contacts, 1=with contacts)___________________| Date of issue: 3/06 SO SSL SERIES SSL 001 ||| ||| ||| Page ...