DE2F3KH103MA3B Murata Electronics, DE2F3KH103MA3B Datasheet - Page 17

• Manufacturer Part Number: DE2F3KH103MA3B
• Description: Cap Ceramic 0.01uF 250VAC F 20% 16 X 7mm RDL 7.5mm Bulk
• Manufacturer: Murata Electronics
• Type: Radialr

Specifications of DE2F3KH103MA3B

• Package/case: 16(Max) X 7(Max)
• Lead Pitch For Radial: 7.5 mm
• Capacitance Value: 0.01 uF
• Dielectric: F
• Tolerance: 20 %
• Voltage: 250 Vac
• Product Depth: 7(Max) mm

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
18
19
*
*
Specifications and Test Methods
1
2
"C" expresses nominal capacitance value (pF).
"room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued from the preceding page.
Passive Flammability
Temperature
and
Immersion
Cycle
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
Change
D.F.
Q
I.R.
Dielectric
Strength
The burning time should not exceed 30 sec.
The tissue paper should not ignite.
No marked defect
3000MΩ min.
Per Item 6
Char.
Char.
E, F
B, E
SL
SL
B
F
QU275+5/2C *
QU350
Capacitance Change
Specifications
Specifications
Within ±10%
Within ±20%
Within ± 5%
D.F.V5.0%
D.F.V7.5%
Type KY/KH/KX Specifications and Test Methods
1
(CF30pF)
(CU30pF)
The capacitor under test should be held in the flame in the
position which best promotes burning. Each specimen should
only be exposed once to the flame. Time of exposure to flame:
30 sec.
The capacitor should be subjected to 5 temperature cycles,
then consecutively to 2 immersion cycles.
Pre-treatment:
Post-treatment:
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
Capacitor should be stored for 24±2 hrs. at room condition*
Step
Step
1
2
1
2
3
4
Temperature (ºC)
Length of flame : 12±1mm
Gas burner
Gas
2
65+5/-0
45
for 24±2 hrs.
0±3
Temperature (ºC)
<Temperature Cycle>
<Immersion Cycle>
Room temp.
Room temp.
125+3/-0
-25+0/-3
Test Method
: Length 35mm min.
: Butane gas Purity 95% min.
Inside Dia.
Outside Dia. 0.9mm max.
Tissue
About 10mm Thick Board
Time
(min)
15
15
Test Specimen
Cycle time: 5 cycle
Cycle time: 2 cycle
0.5±0.1mm
Immersion
Time (min)
Water
Clean
water
water
Salt
30
30
3
3
2
.
C85E.pdf
15
08.10.29
4