DEBB33D102KN2A Murata Electronics, DEBB33D102KN2A Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/4/465/murata_electronics_sml.jpg)
DEBB33D102KN2A
Manufacturer Part Number
DEBB33D102KN2A
Description
Cap Ceramic 0.001uF 2000VDC B 10% 8 X 5mm RDL 5mm Ammo Pack
Manufacturer
Murata Electronics
Type
Radialr
Datasheet
1.DEBB33A681KA2B.pdf
(72 pages)
Specifications of DEBB33D102KN2A
Package/case
8(Max) X 5(Max)
Lead Pitch For Radial
5 mm
Capacitance Value
0.001 uF
Dielectric
B
Tolerance
10 %
Voltage
2000 Vdc
Product Depth
5(Max) mm
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
! Apply to DEJ Series
Operating Temperature Range: -25 to +85°C
No.
1
2
3
4
5
6
7
8
9
Appearance and Dimensions
Marking
Capacitance
Dissipation Factor
(D.F.)
Insulation Resistance (I.R.)
Dielectric
Strength
Temperature Characteristics
Discharge
Test
Solderability of Leads
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Between Lead
Wires
Body
Insulation
Appearance
I.R.
Dielectric
Strength
(Products which are based on the electrical appliance and material safety law of Japan)
No marked defect on appearance form and
dimensions are within specified range.
To be easily legible
Within specified tolerance
10000MΩ min.
No failure
No failure
No marked defect
1000MΩ min.
Per Item 6
Lead wire should be soldered with uniform coating
on the axial direction over 3/4 of the circumferential
direction.
Char.
Char.
E
E
F
F
Capacitance Change
Specifications
Specifications
Within
Within
D.F.V2.5%
D.F.V5.0%
+20
+30
-55
-80
DEJ Series Specifications and Test Methods
%
%
The capacitor should be visually inspected for evidence of
defect.
Dimensions should be measured with slide calipers.
The capacitor should be visually inspected.
The capacitance should be measured at 20˚C with 1±0.1kHz
and AC5V(r.m.s.) max.
The dissipation factor should be measured at 20˚C with
1±0.1kHz and AC5V(r.m.s.) max.
The insulation resistance should be measured with
DC500±50V within 60±5 sec. of charging.
The capacitor should not be damaged when AC1500V(r.m.s.)
are applied between the lead wires for 60 sec.
First, the terminals of the capacitor should be connected
together. Then, as shown in figure at right,
the capacitor should be immersed
into 10% salt solution up to a position
of about 3 to 4mm apart from the
terminals.
Finally, AC1500V(r.m.s.) is applied
for 60 sec. between the capacitor lead
wires and electrode plate.
The capacitance measurement should be made at each step
specified in Table 1.
As in Figure 1, discharge is made 50 times at 5 sec. intervals
from the capacitor (Cd) charged at DC voltage of specified.
Ct: Capacitor under test
S: High-voltage switch
R
The lead wire of a capacitor should be dipped into molten
solder for 2±0.5 sec.
The depth of immersion is up to about 1.5 to 2.0mm from the
root of lead wires.
Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 245±5°C
1
: 1000Ω
Step
Cd
Vs
1
2
3
4
5
Vs
H63 Eutectic Solder 235±5°C
<Table 1>
Temperature (ºC)
R
3
0.001µF
DC10kV
Test Method
-25±2
20±2
20±2
85±2
20±2
S
Fig.1
Continued on the following page.
Cd
R
R
2
3
: 100MΩ
: Surge resistance
R
1
Ct
10% Salt Solution
R
2
About
3 to 4mm
Electrode
Plate
C85E.pdf
17
08.10.29
5