GA355QR7GB103KW01L Murata Electronics, GA355QR7GB103KW01L Datasheet - Page 178

• Manufacturer Part Number: GA355QR7GB103KW01L
• Manufacturer: Murata Electronics

!Note
160
No.
12
13 to Soldering
14
15
16 Life
* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
GRM/DC3.15kV Series Specifi cations and Test Methods
Continued from the preceding page.
Solderability of
Termination
Heat
Temperature
Cycle
Humidity
(Steady
State)
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
Item
Appearance
Capacitance
Change
Q
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q
I.R.
Dielectric
Strength
75% of the terminations are to be soldered evenly
and continuously.
No marking defects
Within ±2.5%
1,000 min.
More than 10,000MΩ
In accordance with item No.4
No marking defects
Within ±2.5%
1,000 min.
More than 10,000MΩ
In accordance with item No.4
No marking defects
Within ±5.0%
350 min.
More than 1,000MΩ
In accordance with item No.4
No marking defects
Within ±3.0%
350 min.
More than 1,000MΩ
In accordance with item No.4
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Immerse in
solder solution for 2±0.5 sec.
Immersing speed: 25±2.5mm/s
Temp. of solder: 245±5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)
Preheat the capacitor as in table.
Immerse the capacitor in solder solution at 260±5°C for 10±1 sec.
Let sit at room condition* for 24±2 hrs., then measure.
*Preheating
Fix the capacitor to the supporting jig (glass epoxy board) shown
in Fig. 4.
Perform the 5 cycles according to the 4 heat treatments listed in
the following table.
Let sit for 24±2 hrs. at room condition,* then measure.
Let the capacitor sit at 40±2°C and relative humidity of 90 to 95%
for 500
Remove and let sit for 24±2 hrs. at room condition,* then
measure.
Apply 120% of the rated voltage for 1,000
operating temperature ±3°C.
Remove and let sit for 24±2 hrs. at room condition,* then
measure.
The charge/discharge current is less than 50mA.
Step
Step
W24
Y
1
2
1
2
3
4
0
hrs.
Max. Operating Temp.±2
Min. Operating Temp.±3
235±5°C H60A or H63A Eutectic Solder
Glass Epoxy Board
Temperature (°C)
: 25±2.5mm/s
Temperature
100 to 120°C
170 to 200°C
Room Temp.
Room Temp.
Fig. 4
Solder resist
Cu
W48
Y
0
Time (min.)
hrs. at maximum
1 min.
1 min.
2 to 3
2 to 3
Time
30±3
30±3
C02E.pdf
Oct.1,2012