EPM7064AETC44-7 Altera, EPM7064AETC44-7 Datasheet - Page 24
![IC MAX 7000 CPLD 64 44-TQFP](/photos/6/70/67053/544-44-tqfp_sml.jpg)
EPM7064AETC44-7
Manufacturer Part Number
EPM7064AETC44-7
Description
IC MAX 7000 CPLD 64 44-TQFP
Manufacturer
Altera
Series
MAX® 7000Ar
Datasheet
1.EPM7032AELC44-10N.pdf
(64 pages)
Specifications of EPM7064AETC44-7
Programmable Type
In System Programmable
Delay Time Tpd(1) Max
7.5ns
Voltage Supply - Internal
3 V ~ 3.6 V
Number Of Logic Elements/blocks
4
Number Of Macrocells
64
Number Of Gates
1250
Number Of I /o
36
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
44-TQFP, 44-VQFP
Voltage
3.3V
Memory Type
EEPROM
Number Of Logic Elements/cells
4
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Features
-
Other names
544-1193
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EPM7064AETC44-7
Manufacturer:
ALTERA
Quantity:
698
Part Number:
EPM7064AETC44-7
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Part Number:
EPM7064AETC44-7N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
MAX 7000A Programmable Logic Device Data Sheet
Programmable
Speed/Power
Control
Output
Configuration
24
MAX 7000A devices offer a power-saving mode that supports low-power
operation across user-defined signal paths or the entire device. This
feature allows total power dissipation to be reduced by 50% or more
because most logic applications require only a small fraction of all gates to
operate at maximum frequency.
The designer can program each individual macrocell in a MAX 7000A
device for either high-speed (i.e., with the Turbo Bit
or low-power operation (i.e., with the Turbo Bit option turned off). As a
result, speed-critical paths in the design can run at high speed, while the
remaining paths can operate at reduced power. Macrocells that run at low
power incur a nominal timing delay adder (t
t
MAX 7000A device outputs can be programmed to meet a variety of
system-level requirements.
MultiVolt I/O Interface
The MAX 7000A device architecture supports the MultiVolt I/O interface
feature, which allows MAX 7000A devices to connect to systems with
differing supply voltages. MAX 7000A devices in all packages can be set
for 2.5-V, 3.3-V, or 5.0-V I/O pin operation. These devices have one set of
VCC pins for internal operation and input buffers (VCCINT), and another
set for I/O output drivers (VCCIO).
The VCCIO pins can be connected to either a 3.3-V or 2.5-V power supply,
depending on the output requirements. When the VCCIO pins are
connected to a 2.5-V power supply, the output levels are compatible with
2.5-V systems. When the VCCIO pins are connected to a 3.3-V power
supply, the output high is at 3.3 V and is therefore compatible with 3.3-V
or 5.0-V systems. Devices operating with V
incur a slightly greater timing delay of t
always be driven by 2.5-V, 3.3-V, or 5.0-V signals.
Table 12
EN
Table 12. MAX 7000A MultiVolt I/O Support
, t
V
CCIO
SEXP
2.5
3.3
Voltage
describes the MAX 7000A MultiVolt I/O support.
, t
ACL
, and t
CPPW
2.5
v
v
Input Signal (V)
parameters.
3.3
v
v
OD2
5.0
v
v
CCIO
instead of t
LPA
) for the t
levels lower than 3.0 V
2.5
v
Output Signal (V)
TM
Altera Corporation
option turned on)
OD1
LAD
3.3
v
. Inputs can
, t
LAC
, t
5.0
v
IC
,