CY7C373I-100JC Cypress Semiconductor Corp, CY7C373I-100JC Datasheet - Page 4

• Manufacturer Part Number: CY7C373I-100JC
• Description: IC CPLD 64 MACROCELL 84-PLCC
• Manufacturer: Cypress Semiconductor Corp
• Series: Ultralogic™r

Specifications of CY7C373I-100JC

• Memory Type: FLASH
• Programmable Type: In-System Reprogrammable™ (ISR™) Flash
• Delay Time Tpd(1) Max: 12.0ns
• Voltage Supply - Internal: 4.75 V ~ 5.25 V
• Number Of Logic Elements/blocks: 4
• Number Of Macrocells: 64
• Number Of I /o: 64
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 84-PLCC
• Voltage: 3.3V/5V
• Family Name: FLASH370i
• # Macrocells: 64
• Number Of Usable Gates: 1600
• Propagation Delay Time: 12ns
• Number Of Logic Blocks/elements: 4
• # I/os (max): 64
• Operating Supply Voltage (typ): 5V
• In System Programmable: Yes
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 84
• Package Type: PLCC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Number Of Logic Elements/cells: -
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant
• Other names: 428-1269

Maximum Ratings
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Storage Temperature ...................................–65 C to +150 C
Ambient Temperature with
Power Applied...............................................–55 C to +125 C
Supply Voltage to Ground Potential ............... –0.5V to +7.0V
DC Voltage Applied to Outputs
in High Z State ............................................... –0.5V to +7.0V
DC Input Voltage............................................ –0.5V to +7.0V
DC Program Voltage .....................................................12.5V
Output Current into Outputs.........................................16 mA
Electrical Characteristics
Document #: 38-03030 Rev. **
V
V
V
V
V
I
I
I
I
I
I
I
I
Notes:
Parameter
IX
OZ
OS
CC
BHL
BHH
BHLO
BHHO
2.
3.
4.
5.
6.
OH
OHZ
OL
IH
IL
If V
I
When the I/O is three-stated, the bus-hold circuit can weakly pull the I/O to a maximum of 4.0V if no leakage current is allowed. This voltage is lowered
significantly by a small leakage current. Note that all I/Os are three-stated during ISR programming. Refer to the application note “Understanding Bus Hold”
for additional information.
These are absolute values with respect to device ground. All overshoots due to system or tester noise are included.
Not more than one output should be tested at a time. Duration of the short circuit should not exceed 1 second. V
caused by tester ground degradation.
OH
CCIO
= –2 mA, I
is not specified, the device can be operating in either 3.3V or 5V I/O mode; V
Output HIGH Voltage
Output HIGH Voltage
with Output Disabled
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input Load Current
Output Leakage Current V
Output Short
Circuit Current
Power Supply Current
Input Bus Hold LOW
Sustaining Current
Input Bus Hold HIGH
Sustaining Current
Input Bus Hold LOW
Overdrive Current
Input Bus Hold HIGH
Overdrive Current
OL
= 2 mA for SDO.
Description
[6, 7]
Over the Operating Range
[7]
[8]
V
V
V
Guaranteed Input Logical HIGH Voltage for all Inputs
Guaranteed Input Logical LOW Voltage for all Inputs
V
V
V
V
f = 1 MHz, V
V
V
V
V
CC
CC
CC
I
CC
CC
CC
CC
CC
CC
CC
CC
= Internal GND, V
= Min.
= Min.
= Max., V
= Max., I
= Min., V
= Min., V
= Max.
= Max.
= Max.
= Max., V
= Max., V
IN
OUT
IL
IH
OUT
= GND, V
I
I
I
I
O
O
= 0.8V
OH
OH
OH
OL
= 2.0V
= GND or V
= 3.3V, Output Disabled
= 0 mA,
= 0.5V
= 16 mA (Com’l/Ind)
= –3.2 mA (Com’l/Ind)
= 0 A (Com’l/Ind)
= –50 A (Com’l/Ind)
[2]
I
Test Conditions
= V
CC
CC
Static Discharge Voltage ........................................... >2001V
(per MIL–STD–883, Method 3015)
Latch-Up Current..................................................... >200 mA
Operating Range
Commercial
Industrial
O
Range
= V
CC
CC
=V
CCINT
, Output Disabled
[3]
[3, 4]
[3]
Com’l/Ind.
Com’l “L”, –66
[3, 4]
.
[4]
Temperature
0 C to +70 C
40 C to +85 C
Ambient
OUT
[5]
[5]
= 0.5V has been chosen to avoid test problems
Min.
–0.5
–10
–50
–30
+75
–75
2.4
2.0
0
5V
5V
V
V
CCINT
Typ.
–70
CC
0.25V
75
45
0.5V
CY7C373i
Max.
–125
–160
+500
–500
+10
+50
125
Page 4 of 13
4.0
3.6
0.5
7.0
0.8
3.3V
3.3V
75
5V
5V
V
OR
OR
CCIO
0.25V
0.5V
Unit
0.3V
0.3V
mA
mA
mA
V
V
V
V
V
V
A
A
A
A
A
A
A