PVZ2A501A01R00 Murata, PVZ2A501A01R00 Datasheet - Page 22
![Trimmer Resistors - SMD 500 OHM SMD 2MM](/photos/16/33/163349/poz2anpt_sml.jpg)
PVZ2A501A01R00
Manufacturer Part Number
PVZ2A501A01R00
Description
Trimmer Resistors - SMD 500 OHM SMD 2MM
Manufacturer
Murata
Datasheets
1.PVM4A501D01R00.pdf
(1 pages)
2.PVZ2A102A01R00.pdf
(6 pages)
3.PVG5A201C01R00.pdf
(90 pages)
Specifications of PVZ2A501A01R00
Resistance
500 Ohms
Tolerance
30 %
Power Rating
0.1 Watt (1/10 Watt)
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Number Of Turns
1
Product
Single-Turn Trimmer Potentiometers
Taper
Linear
Termination Style
SMD/SMT
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PVZ2A501A01R00
Manufacturer:
Murata
Quantity:
7 011
Company:
Part Number:
PVZ2A501A01R00(POZ2AN-1-501N-T
Manufacturer:
MURATA
Quantity:
3 456
!Note
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
4. If the trimmer potentiometer is used in DC and high
1. Soldering
(1) Standard solder iron condition
(2) Use our standard land dimension. Excessive land
(3) The soldering iron should not come in contact
(4) Cannot be soldered using the flow soldering
the power depending on the resistance value.
potentiometer should not exceed (P.R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
humidity conditions, please connect wiper (#2) for
plus and resistive element (#1 or #3) for minus.
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
Notice (Rating)
Notice (Soldering and Mounting)
(a) Reflow soldering:
(b) Sodering iron:
Before using other soldering conditions than
those listed above, please consult with a Murata
factory representative prior to using. If the
soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the trimmer potentiometer may deviate from the
specified characteristics.
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
method. If you use the flow soldering method,
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
>Temperature of tip 260 deg. C max.
>Soldering time
>Diameter
>Wattage of iron
Refer to the standard temperature profile.
1mm dia. max.
3 sec. max.
30W max.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(1) Use our standard land dimension. Excessive land
(2) Do not apply excessive force (preferably 4.9N
(3) Do not warp and/or bend PC board to prevent
(1) Isopropyl-alcohol and Ethyl-alcohol are
(2) The total cleaning time by cold dipping, vapor
(3) For ultra-sonic cleaning, the available
the following environmental conditions:
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
the trimmer potentiometer may not function.
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(Ref.; 500gf) max.), when the trimmer
potentiometer is mounted to the PCB.
trimmer potentiometer from breakage.
applicable solvents for cleaning. If you use any
other types of solvents, please consult with a
Murata factory representative prior to using.
and ultrasonic washing (conditions as below)
method should be less than 3 minutes.
condition is as follows.
Due to the ultra-sonic cleaning equipment's
peculiar self-resonance point and that the
>Power: 600W (67 liter) max.
>Frequency: 28kHz
>Temperature: Ambient temperature
PVF2 Series Notice
Continued on the following page.
R50E13.pdf 04.6.11
21
3