EP1K10TC144-1 Altera, EP1K10TC144-1 Datasheet - Page 40
![IC ACEX 1K FPGA 10K 144-TQFP](/photos/6/70/67061/544-144-tqfp_sml.jpg)
EP1K10TC144-1
Manufacturer Part Number
EP1K10TC144-1
Description
IC ACEX 1K FPGA 10K 144-TQFP
Manufacturer
Altera
Series
ACEX-1K®r
Datasheet
1.EP1K10TC100-3N.pdf
(86 pages)
Specifications of EP1K10TC144-1
Number Of Logic Elements/cells
576
Number Of Labs/clbs
72
Total Ram Bits
12288
Number Of I /o
92
Number Of Gates
56000
Voltage - Supply
2.375 V ~ 2.625 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 70°C
Package / Case
144-TQFP, 144-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP1K10TC144-1
Manufacturer:
ALTERA
Quantity:
5 530
Company:
Part Number:
EP1K10TC144-1
Manufacturer:
SAM
Quantity:
2 000
Company:
Part Number:
EP1K10TC144-1N
Manufacturer:
ALTERA
Quantity:
149
ACEX 1K Programmable Logic Device Family Data Sheet
40
PCI Pull-Up Clamping Diode Option
ACEX 1K devices have a pull-up clamping diode on every I/O, dedicated
input, and dedicated clock pin. PCI clamping diodes clamp the signal to
the V
diodes can also be used to limit overshoot in other systems.
Clamping diodes are controlled on a pin-by-pin basis. When V
3.3 V, a pin that has the clamping diode option turned on can be driven by
a 2.5-V or 3.3-V signal, but not a 5.0-V signal. When V
that has the clamping diode option turned on can be driven by a 2.5-V
signal, but not a 3.3-V or 5.0-V signal. Additionally, a clamping diode can
be activated for a subset of pins, which allows a device to bridge between
a 3.3-V PCI bus and a 5.0-V device.
Slew-Rate Control
The output buffer in each IOE has an adjustable output slew rate that can
be configured for low-noise or high-speed performance. A slower slew
rate reduces system noise and adds a maximum delay of 4.3 ns. The fast
slew rate should be used for speed-critical outputs in systems that are
adequately protected against noise. Designers can specify the slew rate
pin-by-pin or assign a default slew rate to all pins on a device-wide basis.
The slow slew rate setting affects only the falling edge of the output.
Open-Drain Output Option
ACEX 1K devices provide an optional open-drain output (electrically
equivalent to open-collector output) for each I/O pin. This open-drain
output enables the device to provide system-level control signals (e.g.,
interrupt and write enable signals) that can be asserted by any of several
devices. It can also provide an additional wired-OR plane.
MultiVolt I/O Interface
The ACEX 1K device architecture supports the MultiVolt I/O interface
feature, which allows ACEX 1K devices in all packages to interface with
systems of differing supply voltages. These devices have one set of V
pins for internal operation and input buffers (VCCINT), and another set for
I/O output drivers (VCCIO).
CCIO
value and are required for 3.3-V PCI compliance. Clamping
CCIO
Altera Corporation
is 2.5 V, a pin
CCIO
is
CC