EP4CE40F29C8N Altera, EP4CE40F29C8N Datasheet - Page 7

• Manufacturer Part Number: EP4CE40F29C8N
• Description: IC CYCLONE IV FPGA 40K 780FBGA
• Manufacturer: Altera
• Series: CYCLONE® IV Er

Specifications of EP4CE40F29C8N

• Number Of Logic Elements/cells: 39600
• Number Of Labs/clbs: 2475
• Total Ram Bits: 1134000
• Number Of I /o: 532
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 780-FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -

Chapter 1: Cyclone IV Device Datasheet
Operating Conditions
DC Characteristics
Table 1–6. I/O Pin Leakage Current for Cyclone IV Devices
Table 1–7. Bus Hold Parameter for Cyclone IV Devices (Part 1 of 2)
© December 2010 Altera Corporation
I
I
Notes to
(1) This value is specified for normal device operation. The value varies during device power
(2) The 10 A I/O leakage current limit is applicable when the internal clamping diode is off. A higher current can be observed when the diode is on.
Bus hold
low,
sustaining
current
Bus hold
high,
sustaining
current
Bus hold
low,
overdrive
current
Bus hold
high,
overdrive
current
Symbol
I
OZ
Parameter
1.8, 1.5, and 1.2 V).
Table
Input pin leakage current
Tristated I/O pin leakage
current
1–6:
V
(maximum)
V
(minimum)
0 V < V
0 V < V
IN
IN
Parameter
Condition
> V
< V
IL
IL
IN
IN
This section lists the I/O leakage current, pin capacitance, on-chip termination (OCT)
tolerance, and bus hold specifications for Cyclone IV devices.
Supply Current
The device supply current requirement is the minimum current drawn from the
power supply pins that can be used as a reference for power size planning. Use the
Excel-based early power estimator (EPE) to get the supply current estimates for your
design because these currents vary greatly with the resources used.
I/O pin leakage current for Cyclone IV devices.
Bus Hold
The bus hold retains the last valid logic state after the source driving it either enters
the high impedance state or is removed. Each I/O pin has an option to enable bus
hold in user mode. Bus hold is always disabled in configuration mode.
Table 1–7
< V
< V
CCIO
CCIO
Min
lists bus hold specifications for Cyclone IV devices.
–8
—
—
8
1.2
V
V
I
O
–125
Max
= 0 V to V
125
= 0 V to V
—
—
Conditions
Min
–12
12
—
—
CCIOMAX
CCIOMAX
1.5
–175
Max
175
—
—
(Note 1)
Min
–30
30
—
—
,
Device
1.8
(2)
(Note
—
—
–200
Max
200
V
—
—
CCIO
1)—Preliminary
(V)
-
up. This applies for all V
Min
–50
50
—
—
2.5
–300
Max
300
Min
–10
–10
—
—
Cyclone IV Device Handbook, Volume 3
Min
–70
70
—
—
3.0
Typ
—
—
CCIO
–500
Max
500
—
—
Table 1–6
settings (3.3, 3.0, 2.5,
Min
–70
Max
70
—
—
10
10
3.3
lists the
–500
Max
500
—
—
Unit
A
A
1–7
Unit
A
A
A
A