EP1S40B956C6 Altera, EP1S40B956C6 Datasheet - Page 77
![IC STRATIX FPGA 40K LE 956-BGA](/photos/6/73/67334/544-stratix_956-bga_sml.jpg)
EP1S40B956C6
Manufacturer Part Number
EP1S40B956C6
Description
IC STRATIX FPGA 40K LE 956-BGA
Manufacturer
Altera
Series
Stratix®r
Datasheet
1.EP1S10F780C7.pdf
(276 pages)
Specifications of EP1S40B956C6
Number Of Logic Elements/cells
41250
Number Of Labs/clbs
4125
Total Ram Bits
3423744
Number Of I /o
683
Voltage - Supply
1.425 V ~ 1.575 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
956-BGA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Other names
544-1423
EP1S40SB956C6
EP1S40SB956C6
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP1S40B956C6
Manufacturer:
ALTERA
Quantity:
260
Company:
Part Number:
EP1S40B956C6
Manufacturer:
ALTERA
Quantity:
3 000
Part Number:
EP1S40B956C6
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Company:
Part Number:
EP1S40B956C6N
Manufacturer:
ALTERA
Quantity:
229
Part Number:
EP1S40B956C6N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Altera Corporation
July 2005
Adder/Subtractor/Accumulator
The adder/subtractor/accumulator is the first level of the adder/output
block and can be used as an accumulator or as an adder/subtractor.
Adder/Subtractor
Each adder/subtractor/accumulator block can perform addition or
subtraction using the addnsub independent control signal for each first-
level adder in 18 × 18-bit mode. There are two addnsub[1..0] signals
available in a DSP block for any configuration. For 9 × 9-bit mode, one
addnsub[1..0] signal controls the top two one-level adders and
another addnsub[1..0] signal controls the bottom two one-level
adders. A high addnsub signal indicates addition, and a low signal
indicates subtraction. The addnsub control signal can be unregistered or
registered once or twice when feeding the adder blocks to match data
path pipelines.
The signa and signb signals serve the same function as the multiplier
block signa and signb signals. The only difference is that these signals
can be registered up to two times. These signals are tied to the same
signa and signb signals from the multiplier and must be connected to
the same clocks and control signals.
Accumulator
When configured for accumulation, the adder/output block output feeds
back to the accumulator as shown in
accum_sload[1..0] signal synchronously loads the multiplier result
to the accumulator output. This signal can be unregistered or registered
once or twice. Additionally, the overflow signal indicates the
accumulator has overflowed or underflowed in accumulation mode. This
signal is always registered and must be externally latched in LEs if the
design requires a latched overflow signal.
Summation
The output of the adder/subtractor/accumulator block feeds to an
optional summation block. This block sums the outputs of the DSP block
multipliers. In 9 × 9-bit mode, there are two summation blocks providing
the sums of two sets of four 9 × 9-bit multipliers. In 18 × 18-bit mode, there
is one summation providing the sum of one set of four 18 × 18-bit
multipliers.
Figure
Stratix Device Handbook, Volume 1
2–34. The
Stratix Architecture
2–63