133-3404-101 Emerson Network Power, 133-3404-101 Datasheet - Page 6

• Manufacturer Part Number: 133-3404-101
• Description: RF Connectors R/A CRIMP PLG GOLD 50 OHM RG-188&316 DS
• Manufacturer: Emerson Network Power
• Type: Cable Plugr

Specifications of 133-3404-101

• Product: Connector
• Rf Series: MCX
• Gender: Plug
• Impedance: 50 Ohms
• Angle: Right Angle
• Cable Type: RG-316DS,188DS
• Contact Plating: Gold
• Finish, Housing: Gold
• Frequency: 0 to 6 GHz
• Insertion Loss: 0.2 dB (Max.) @ 1 GHz
• Material, Contact: Brass
• Material, Dielectric: TFE
• Material, Housing: Brass
• Primary Type: MCX
• Resistance, Contact: 5 Milliohms (Max.) (Center), 1 Milliohms (Max.) (Outer)
• Resistance, Insulation: 1000 Megohms (Min.)
• Special Features: Captivated Contact
• Termination: Crimp
• Voltage, Rating: 335 V
• Plating: Gold Over Brass Except Where Noted
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Assembly
Instructions
MCX CRIMP TYPE
RIGHT ANGLE PLUGS
FOR FLEXIBLE CABLE
6
Johnson Components
®
• P.O. Box 1732 • Waseca, MN 56093-0832 • 1-800-247-8256 • Fax: [phone] • www.johnsoncomp.com
RG 316DS, 188DS
RG 316DS, 188DS
RG 58/u, 303, 141
RG 188/u, 316,
RG 188/u, 316,
RG 178/u, 196
RG 179/u, 187
RG 178/u, 196
161, 174
161, 174
GROUP
CABLE
133-3402-101/106
133-3403-101/106
133-3404-101/106
133-3433-101/106
133-5402-101/106
133-5403-101/106
133-5404-101/106
133-3407-101/106
NUMBER
PART
.050 (1.27)
.050 (1.27)
.050 (1.27)
.050 (1.27)
.050 (1.27)
.050 (1.27)
.050 (1.27)
.067(1.70)
1. Identify connector parts. (4 piece parts
2. Strip cable to dimensions shown. Do not
3. Flair braid and slide cable into body making
4. Solder center conductor to contact through
5. Assemble insulator if applicable then place
"A"
except RG-58)
nick braid or center conductor. A wire
stripper of correct size is recommended for
this step. Twist stranded center conductor
into tight bundle and tin (optional). Slide
crimp sleeve onto cable shown.
certain that the cable insulation bottoms on
center contact. Arrange braid uniformly
around crimp stem. Slide crimp sleeve
over braid and crimp securely using
recommended crimp tool.
rear access port. Use a minimum amount
of solder for a full fillet joint. .020 (0.51)
diameter solder is recommended.
expansion cap in access port and seat with
.156 (3.96) diameter flat punch or MCX
hand assembly tool 141-0000-908. Shrink
heat shrink tubing over crimp sleeve if
applicable.
.270 (6.86)
.270 (6.86)
.270 (6.86)
.270 (6.86)
.270 (6.86)
.270 (6.86)
.270 (6.86)
.295 (7.49)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
"B"
.200 (5.08)
.200 (5.08)
.200 (5.08)
.200 (5.08)
.200 (5.08)
.200 (5.08)
.200 (5.08)
.210 (5.33)
"C"
INCHES (MILLIMETERS)
.105 (2.67)
.128 (3.25)
.151 (3.83)
.128 (3.25)
.105 (2.67)
.128 (3.25)
.151 (3.83)
.213 (5.41)
CRIMP
HEX