20-101-1246 Rabbit Semiconductor, 20-101-1246 Datasheet - Page 22
20-101-1246
Manufacturer Part Number
20-101-1246
Description
CORE MODULE RCM5400W
Manufacturer
Rabbit Semiconductor
Datasheet
1.20-101-1246.pdf
(120 pages)
Specifications of 20-101-1246
Module/board Type
MPU Core Module
Wireless Frequency
73.73 MHz
For Use With/related Products
RCM5400W
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1148
- Current page: 22 of 120
- Download datasheet (2Mb)
2.3.1 Troubleshooting
If you receive the message
assigned to the USB programming cable was identified and set up in Dynamic C as
described in the preceding section.
If you receive the message No Rabbit Processor Detected, the programming
cable may be connected to the wrong COM port, a connection may be faulty, or the target
system may not be powered up. First, check to see that the power LED on the Prototyping
Board is lit. If the LED is lit, check both ends of the programming cable to ensure that it is
firmly plugged into the PC and the programming header on the RCM5400W with the
marked (colored) edge of the programming cable towards pin 1 of the programming
header. Ensure that the module is firmly and correctly installed in its connectors on the
Prototyping Board.
If Dynamic C appears to compile the BIOS successfully, but you then receive a communi-
cation error message when you compile and load a sample program, it is possible that your
PC cannot handle the higher program-loading baud rate. Try changing the maximum
download rate to a slower baud rate as follows.
• Locate the
If a program compiles and loads, but then loses target communication before you can
begin debugging, it is possible that your PC cannot handle the default debugging baud
rate. Try lowering the debugging baud rate as follows.
• Locate the
Press
compiled successfully
16
Options > Project Options
to save.
Options > Project Options
<Ctrl-Y>
Serial Options
Serial Options
to force Dynamic C to recompile the BIOS. You should receive a
Could Not Open Serial Port
message once this step is completed successfully.
dialog on the “Communications” tab in the Dynamic C
dialog on the “Communications” tab in the Dynamic C
menu. Select a slower Max download baud rate. Click
menu. Choose a lower debug baud rate. Click
, check that the COM port
RabbitCore RCM5400W
OK
Bios
to save.
OK
Related parts for 20-101-1246
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: