CY7C68013A-100AXC Cypress Semiconductor Corp, CY7C68013A-100AXC Datasheet - Page 22

• Manufacturer Part Number: CY7C68013A-100AXC
• Description: IC MCU USB PERIPH HI SPD 100LQFP
• Manufacturer: Cypress Semiconductor Corp
• Series: EZ-USB FX2LP™r

Specifications of CY7C68013A-100AXC

• Program Memory Type: ROMless
• Package / Case: 100-LQFP
• Applications: USB Microcontroller
• Core Processor: 8051
• Controller Series: CY7C680xx
• Ram Size: 16K x 8
• Interface: I²C, USB, USART
• Number Of I /o: 40
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Processor Series: CY7C68xx
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 16 KB
• Interface Type: I2C/USART/USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 40
• Number Of Timers: 3
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: CY3684
• Minimum Operating Temperature: 0 C
• Cpu Family: FX2LP
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 48MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 16KB
• # I/os (max): 40
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: TQFP
• Package: 100TQFP
• Family Name: FX2LP
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 3.3 V
• Controller Family/series: (8051) USB
• Core Size: 8 Bit
• No. Of I/o's: 40
• Cpu Speed: 48MHz
• No. Of Timers: 3
• Embedded Interface Type: I2C, USART, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: CY4611B - KIT USB TO ATA REFERENCE DESIGN428-1677 - KIT DEVELOPMENT EZ-USB FX2LP
• Lead Free Status / Rohs Status: Compliant
• Other names: 428-1667

Table 11. FX2LP Pin Descriptions (continued)
Document #: 38-08032 Rev. *M
TQFP
Port A
128
34
99
35
12
82
83
84
11
1
TQFP
100
100
28
77
10
67
68
69
11
SSOP
56
49
12
40
41
42
11
5
QFN
56
42
54
33
34
35
5
4
56 VF-
BGA
8G
6G
8B
1C
2C
2B
8F
BKPT
RESET#
EA
XTALIN
XTALOUT
CLKOUT on
CY7C68013A
and
CY7C68014A
------------------
PE1 on
CY7C68015A
and
CY7C68016A
PA0 or
INT0#
PA1 or
INT1#
PA2 or
SLOE or
Name
-----------
Output
Output
Type
Input
Input
Input
I/O/Z
I/O/Z
I/O/Z
I/O/Z
O/Z
Default
12 MHz
----------
(PA0)
(PA1)
(PA2)
N/A
N/A
N/A
N/A
L
I
I
I
I
Breakpoint. This pin goes active (HIGH) when the 8051
address bus matches the BPADDRH/L registers and
breakpoints are enabled in the BREAKPT register
(BPEN = 1). If the BPPULSE bit in the BREAKPT
register is HIGH, this signal pulses HIGH for eight
12-/24-/48-MHz clocks. If the BPPULSE bit is LOW, the
signal remains HIGH until the 8051 clears the BREAK
bit (by writing 1 to it) in the BREAKPT register.
Active LOW Reset. Resets the entire chip. See section
3.9 ”Reset and Wakeup” on page 6 for more details.
External Access. This pin determines where the 8051
fetches code between addresses 0x0000 and 0x3FFF.
If EA = 0 the 8051 fetches this code from its internal
RAM. IF EA = 1 the 8051 fetches this code from external
memory.
Crystal Input. Connect this signal to a 24-MHz
parallel-resonant, fundamental mode crystal and load
capacitor to GND.
It is also correct to drive XTALIN with an external
24-MHz square wave derived from another clock
source. When driving from an external source, the
driving signal should be a 3.3V square wave.
Crystal Output. Connect this signal to a 24-MHz
parallel-resonant, fundamental mode crystal and load
capacitor to GND.
If an external clock is used to drive XTALIN, leave this
pin open.
CLKOUT: 12-, 24- or 48-MHz clock, phase locked to the
24-MHz input clock. The 8051 defaults to 12-MHz
operation. The 8051 may three-state this output by
setting CPUCS.1 = 1.
------------------------------------------------------------------------
PE1 is a bidirectional I/O port pin.
Multiplexed pin whose function is selected by
PORTACFG.0
PA0 is a bidirectional I/O port pin.
INT0# is the active-LOW 8051 INT0 interrupt input
signal, which is either edge triggered (IT0 = 1) or level
triggered (IT0 = 0).
Multiplexed pin whose function is selected by:
PORTACFG.1
PA1 is a bidirectional I/O port pin.
INT1# is the active-LOW 8051 INT1 interrupt input
signal, which is either edge triggered (IT1 = 1) or level
triggered (IT1 = 0).
Multiplexed pin whose function is selected by two bits:
IFCONFIG[1:0].
PA2 is a bidirectional I/O port pin.
SLOE is an input-only output enable with program-
mable polarity (FIFOPINPOLAR.4) for the slave FIFOs
connected to FD[7..0] or FD[15..0].
CY7C68013A, CY7C68014A
CY7C68015A, CY7C68016A
Description
Page 22 of 62
[+] Feedback