CY7C63723-SXC Cypress Semiconductor Corp, CY7C63723-SXC Datasheet - Page 30
![IC MCU 8K LS USB/PS-2 18-SOIC](/photos/6/76/67606/428-18-soic_sml.jpg)
CY7C63723-SXC
Manufacturer Part Number
CY7C63723-SXC
Description
IC MCU 8K LS USB/PS-2 18-SOIC
Manufacturer
Cypress Semiconductor Corp
Series
enCoRe™r
Specifications of CY7C63723-SXC
Applications
USB Microcontroller
Core Processor
M8B
Program Memory Type
OTP (8 kB)
Controller Series
CY7C637xx
Ram Size
256 x 8
Interface
PS2, USB
Number Of I /o
10
Voltage - Supply
4 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
18-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
428-1720-5
CY7C63723-SXC
CY7C63723-SXC
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7C63723-SXC
Manufacturer:
NS
Quantity:
16
Part Number:
CY7C63723-SXC
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
During power-up, or during a low-voltage reset, the Processor
Status and Control Register is set to 00010001, which indicates
a LVR/BOR (bit 4 set) has occurred and no interrupts are pending
(bit 7 clear). Note that during the t
start-up (explained in Section ), a Watchdog Reset will also
occur. When a WDR occurs during the power-up suspend
interval, firmware would read 01010001 from the Status and
Control Register after power-up. Normally the LVR/BOR bit
should be cleared so that a subsequent WDR can be clearly
identified. Note that if a USB bus reset (long SE0) is received
before firmware examines this register, the Bus Interrupt Event
bit would also be set.
During a Watchdog Reset, the Processor Status and Control
Register is set to 01XX0001, which indicates a Watchdog Reset
(bit 4 set) has occurred and no interrupts are pending (bit 7
clear).
Interrupts
Interrupts can be generated by the GPIO lines, the internal
free-running timer, the SPI block, the capture timers, on various
USB events, PS/2 activity, or by the wake-up timer. All interrupts
are maskable by the Global Interrupt Enable Register and the
USB End Point Interrupt Enable Register. Writing a ‘1’ to a bit
position enables the interrupt associated with that bit position.
During a reset, the contents of the interrupt enable registers are
cleared, along with the Global Interrupt enable bit of the CPU,
effectively disabling all interrupts.
The interrupt controller contains a separate flip-flop for each
interrupt. See Figure 36 for the logic block diagram of the
interrupt controller. When an interrupt is generated it is first regis-
tered as a pending interrupt. It will stay pending until it is serviced
or a reset occurs. A pending interrupt will only generate an
interrupt request if it is enabled by the corresponding bit in the
interrupt enable registers. The highest priority interrupt request
will be serviced following the completion of the currently
executing instruction.
When servicing an interrupt, the hardware will first disable all
interrupts by clearing the Global Interrupt Enable bit in the CPU
(the state of this bit can be read at Bit 2 of the Processor Status
and Control Register). Next, the flip-flop of the current interrupt
is cleared. This is followed by an automatic CALL instruction to
the ROM address associated with the interrupt being serviced
(i.e., the Interrupt Vector, see Section ). The instruction in the
interrupt table is typically a JMP instruction to the address of the
Interrupt Service Routine (ISR). The user can re-enable inter-
rupts in the interrupt service routine by executing an EI
instruction. Interrupts can be nested to a level limited only by the
available stack space.
The Program Counter value as well as the Carry and Zero flags
(CF, ZF) are stored onto the Program Stack by the automatic
CALL instruction generated as part of the interrupt acknowledge
process. The user firmware is responsible for ensuring that the
processor state is preserved and restored during an interrupt.
The PUSH A instruction should typically be used as the first
command in the ISR to save the accumulator value and the POP
A instruction should be used just before the RETI instruction to
restore the accumulator value. The program counter, CF and ZF
Document #: 38-08022 Rev. *D
START
ms partial suspend at
are restored and interrupts are enabled when the RETI
instruction is executed.
The DI and EI instructions can be used to disable and enable
interrupts, respectively. These instructions affect only the Global
Interrupt Enable bit of the CPU. If desired, EI can be used to
re-enable interrupts while inside an ISR, instead of waiting for the
RETI that exits the ISR. While the global interrupt enable bit is
cleared, the presence of a pending interrupt can be detected by
examining the IRQ Sense bit (Bit 7 in the Processor Status and
Control Register).
Interrupt Vectors
The Interrupt Vectors supported by the device are listed in
Table
PS/2 activity), and the lowest priority interrupt is #11 (Wake-up
Timer). Although Reset is not an interrupt, the first instruction
executed after a reset is at ROM address 0x0000, which corre-
sponds to the first entry in the Interrupt Vector Table. Interrupt
vectors occupy two bytes to allow for a two-byte JMP instruction
to the appropriate Interrupt Service Routine (ISR).
Table 7. Interrupt Vector Assignments
Interrupt Latency
Interrupt latency can be calculated from the following equation:
Interrupt Latency = (Number of clock cycles remaining in the
For example, if a 5 clock cycle instruction such as JC is being
executed when an interrupt occurs, the first instruction of the
Interrupt Service Routine will execute a minimum of 16 clocks
(1+10+5) or a maximum of 20 clocks (5+10+5) after the interrupt
is issued. With a 6-MHz external resonator, internal CPU clock
speed is 12 MHz, so 20 clocks take 20/12 MHz = 1.67 μs.
not applicable
Vector No.
Interrupt
7. The highest priority interrupt is #1 (USB Bus Reset /
10
11
1
2
3
4
5
6
7
8
9
Address
0x000A
0x000C
0x000E
0x0000
0x0002
0x0004
0x0006
0x0008
0x0010
0x0012
0x0014
0x0016
ROM
current instruction)
+ (10 clock cycles for the CALL instruction)
+ (5 clock cycles for the JMP instruction)
Execution after Reset begins
here
USB Bus Reset or PS/2 Activity
interrupt
128-μs timer interrupt
1.024-ms timer interrupt
USB Endpoint 0 interrupt
USB Endpoint 1 interrupt
USB Endpoint 2 interrupt
SPI Interrupt
Capture Timer A interrupt
Capture Timer B interrupt
GPIO interrupt
Wake-up Timer interrupt
Function
CY7C63722C
CY7C63723C
CY7C63743C
Page 30 of 53
[+] Feedback