EZ80L92AZ020EC00TR Zilog, EZ80L92AZ020EC00TR Datasheet - Page 114
EZ80L92AZ020EC00TR
Manufacturer Part Number
EZ80L92AZ020EC00TR
Description
IC EZ80 MPU 100LQFP
Manufacturer
Zilog
Datasheet
1.EZ80L92AZ020SG.pdf
(231 pages)
Specifications of EZ80L92AZ020EC00TR
Processor Type
eZ80
Features
High Speed, Single-Cycle Instruction-Fetch
Speed
20MHz
Voltage
3.3V
Mounting Type
Surface Mount
Package / Case
100-LQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
EZ80L92AZ020EC00T
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 114 of 231
- Download datasheet (3Mb)
eZ80L92 MCU
Product Specification
108
rupts are enabled (except for the transmit interrupt) and the application is ready to use the
module for transmission/reception.
To transmit data, the application enables the transmit inter-
Data Transfers—Transmit.
rupt. An interrupt is immediately expected in response. The application reads the
UARTx_IIR register and determines that the interrupt occurs due to an empty
UARTx_THR register. When the application determines this occurrence, the application
writes the transmit data bytes to the UARTx_THR register. The number of bytes that the
application writes depends on whether or not the FIFO is enabled. If the FIFO is enabled,
the application can write 16 bytes at a time. If not, the application can write one byte at a
time. As a result of the first Write, the interrupt is deactivated. The processor then waits
for the next interrupt. When the interrupt is raised by the UART module, the processor
repeats the same process until it exhausts all of the data for transmission.
To control and check the modem status, the application sets up the modem by writing to
the UARTx_MCTL register and reading the UARTx_MCTL register before starting the
process mentioned above.
The receiver is always enabled, and it continually checks for
Data Transfers—Receive.
the start bit on the RxD input signal. When an interrupt is raised by the UART module, the
application reads the UARTx_IIR register and determines the cause for the interrupt. If the
cause is a line status interrupt, the application reads the UARTx_LSR register, reads the
data byte and then can discard the byte or take other appropriate action. If the interrupt is
caused by a receive-data-ready condition, the application alternately reads the
UARTx_LSR and UARTx_RBR registers and removes all of the received data bytes. It
reads the UARTx_LSR register before reading the UARTx_RBR register to determine that
there is no error in the received data.
To control and check modem status, the application sets up the modem by writing to the
UARTx_MCTL register and reading the UARTx_MSR register before starting the process
mentioned above.
When interrupts are disabled, all data transfers are referred to as
Poll Mode Transfers.
poll mode transfers. In poll mode transfers, the application must continually poll the
UARTx_LSR register to transmit or receive data without enabling the interrupts. The
same holds true for the UARTx_MSR register. If the interrupts are not enabled, the data in
the UARTx_IIR register cannot be used to determine the cause of interrupt.
Baud Rate Generator
The Baud Rate Generator consists of a 16-bit downcounter, two registers, and associated
decoding logic. The initial value of the Baud Rate Generator is defined by the two BRG
Divisor Latch registers, {UARTx_BRG_H, UARTx_BRG_L}. At the rising edge of each
system clock, the BRG decrements until it reaches the value
. On the next system
0001h
clock rising edge, the BRG reloads the initial value from {UARTx_BRG_H,
PS013014-0107
Universal Asynchronous Receiver/Transmitter
Related parts for EZ80L92AZ020EC00TR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: