ES1-LW50 Omron, ES1-LW50 Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
ES1-LW50
Manufacturer Part Number
ES1-LW50
Description
Sensor Hardware & Accessories INFRARED THERMOSENSORS
Manufacturer
Omron
Datasheet
1.ES1-LW100H.pdf
(64 pages)
Specifications of ES1-LW50
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Precautions for Operation
1. It takes approximately 2 seconds for the outputs to turn ON from
2. When using self-tuning, turn ON power for the load (e.g., heater)
3. When starting operation after the Temperature Controller has
4. Avoid using the Controller in places near a radio, television set, or
USB-Serial Conversion Cable
1. The disk that is included with the Conversion Cable is designed for
2. Do not connect or disconnect the Conversion Cable connector
3. After connecting the Conversion Cable to the computer, check the
4. Do not connect the Conversion Cable through a USB hub. Doing
5. Do not use an extension cable to extend the Conversion Cable
6. For models with communications, the same port is used by the
Mounting
Mounting to the Panel
E5CZ
1. For waterproof mounting, waterproof packing must be installed on
2. Insert the E5CZ/E5CZ-U into the mounting hole in the panel.
3. Push the adapter from the terminals up to the panel, and
4. Tighten the two fastening screws on the adapter. Alternately
Waterproof packing
(Accessory)
after the power supply is turned ON. Due consideration must be
given to this time when incorporating Temperature Controllers in a
sequence circuit.
at the same time as or before supplying power to the Temperature
Controller. If power is turned ON for the Temperature Controller
before turning ON power for the load, self-tuning will not be
performed properly and optimum control will not be achieved.
warmed up, turn OFF the power and then turn it ON again at the
same time as turning ON power for the load. (Instead of turning the
Temperature Controller OFF and ON again, switching from STOP
mode to RUN mode can also be used.)
wireless installing. These devices can cause radio disturbances
which adversely affect the performance of the Controller.
a computer CD-ROM driver. Never attempt to play the disk in a
general-purpose audio player.
repeatedly over a short period of time. The computer may
malfunction.
COM port number before starting communications. The computer
requires time to recognize the cable connection. This delay does
not indicate failure.
so may damage the Conversion Cable.
length when connecting to the computer. Doing so may damage
the Conversion Cable.
Setting Tool port and for communications via the communications
terminals. Do not use communications via the communications
terminals when using the Setting Tool port.
the Controller. Waterproofing is not possible when group mounting
Controllers. Waterproof packing is not necessary when there is no
need for the waterproof function.
There is no waterproof function for the E5CZ-U.
temporarily fasten the E5CZ/E5CZ-U.
tighten the two screws little by little to maintain a balance. Tighten
the screws to a torque of 0.29 to 0.39 N·m.
Terminal Cover
E53-COV17
(order separately)
Panel
Adapter
(order separately)
E5CZ
Order the P2CF-11 or
P3GA-11 Socket separately.
For Front-mounting Socket
(Panel mounting is also possible.)
E5CZ-U
E5EZ/E5AZ
1. For waterproof mounting, waterproof packing must be installed on
2. Insert the E5AZ/E5EZ into the square mounting hole in the panel
3. Use a ratchet to alternately tighten the screws on the top and
Mounting the Terminal Cover
For the E5CZ, make sure the “UP” characters on the Cover are in the
correct position and insert the Cover into the holes at the top and
bottom.
For the E5EZ or E5AZ, fit the E53-COV11 Terminal Cover over the
upper hook. Mount it in the direction shown in the above diagram. If
the Terminal Cover is mounted in the opposite direction, proper
mounting of the fixtures may not be possible.
the Controller. Waterproofing is not possible when group mounting
Controllers. Waterproof packing is not necessary when there is no
need for the waterproof function.
(thickness: 1 to 8 mm). Attach the Mounting Brackets provided
with the product to the mounting grooves on the top and bottom
surfaces of the rear case.
bottom Mounting Brackets little by little to maintain balance, until
the ratchet turns freely.
Terminal Cover
(E53-COV11)
(order separately)
Terminal Cover
(E53-COV11)
Waterproof packing
(Accessory)
Waterproof packing
(Accessory)
Mounting
Bracket
(Accessory)
E5EZ
Mounting
Bracket
(Accessory)
E5AZ
Panel
Panel
E5@Z
35