M2015TJW01-FA-1A-RO NKK Switches, M2015TJW01-FA-1A-RO Datasheet
M2015TJW01-FA-1A-RO
Specifications of M2015TJW01-FA-1A-RO
Related parts for M2015TJW01-FA-1A-RO
M2015TJW01-FA-1A-RO Summary of contents
Page 1
... All models recognized 125V 250V AC or 0.4VA maximum @ 28V DC maximum. Add “/U” to end of part number to order UL mark on switch. File No. 023535_0_000 All models recognized 125V 250V AC or 0.4VA maximum @ 28V maximum. Add “/C” to end of part number to order CSA mark on switch. www.nkk.com Miniature Rockers ...
Page 2
... Bias guard prevents misalignment of contacts; interlocking of actuator block with rocker and internal guide does not allow transmission of diagonal force on rocker to reach contact mechanism. Clinching of the frame to the case well above the base and terminals provides 1,500V dielectric strength. ...
Page 3
... Solder Lug Terminals B64 www.nkk.com TYPICAL SWITCH ORDERING EXAMPLE Rockers & Paddles F .450” (11.43mm) Wide Rocker G .450” (11.43mm) Wide Paddle .453” (11.5mm) False Lug* S Illluminated Rocker in Black only Rocker & Paddle Colors A Black B White C Red E Yellow F Green G Blue H Gray * Wire harness & ...
Page 4
... Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. B66 Snap-In Mount Miniature Rockers POLES & CIRCUITS Connected Terminals ...
Page 5
... Snap-In Mount Miniature Rockers 01 Solder Lug Epoxy Seal (2.0) .079 Thk = (0.8) .031 .250” (6.35mm) 03 Straight PC Epoxy Seal .425” (10.8mm) 05 Wirewrap or Extended PC .750” (19.05mm) 06 Wirewrap or Extended PC .964” (24.5mm) 07 Wirewrap or Extended PC 1.062” (27.0mm) 08 Wirewrap or Extended PC AT4150 F .450” (11.43mm) Wide Rocker (9 ...
Page 6
... Material: (2.0) Typ .079 Polycarbonate Finish: Semi-glossy (8.0) .315 1. Pry out tab on bezel to 2. Insert switch frame under a 45° angle. Tab 45° Tab B68 Snap-In Mount Miniature Rockers A Black (11.8) .465 B White (2.2) .087 C (12.0) .472 Red (21.5) .846 E ...
Page 7
... If the source voltage is greater than the rated voltage of the LED, a ballast resistor must be connected in series with the lamp. The ballast resistor calculation and more lamp detail are shown in the Supplement section. NKK Switches can provide custom legends for caps. Contact factory for more information. Recommended Print Method: Pad Print Epoxy based ink is recommended ...
Page 8
... Snap-in Frame • Solder Lug (18.0) .709 (11.43) .450 M2012TJW01-GC Snap-in Frame • Solder Lug (18.0) .709 (11.43) .450 M2022TJW01-GC B70 Snap-In Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Single Pole (4.9) .194 (2.8) Circuit Mark .110 This Side 25° (0.5) .020 (3.3) (7 ...
Page 9
... Snap-In Mount Miniature Rockers (5.6) .221 (12.0) .472 25° (21.5) .846 (4.3) (11.43) .450 .169 (11.8) (2.2) .465 .087 (15.6) (4.01) (6.4) .614 .158 .252 (5.08) Dia .200 (19.0) .748 (13.5) (30.2) .531 1.190 (12.0) 25° .472 (11.43) .450 (11.8) .465 (4 ...