E2E-X5Y1-M4 Omron, E2E-X5Y1-M4 Datasheet - Page 14
![Proximity Sensors Country of Origin Change Only](/photos/17/82/178294/e2e_grouping_sml.jpg)
E2E-X5Y1-M4
Manufacturer Part Number
E2E-X5Y1-M4
Description
Proximity Sensors Country of Origin Change Only
Manufacturer
Omron
Type
Inductive Proximity Sensorr
Series
E2Er
Datasheet
1.E2E-X10Y1-53-US.pdf
(16 pages)
Specifications of E2E-X5Y1-M4
Maximum Operating Temperature
+ 85 C
Mounting Style
Panel
Sensing Distance
5 mm
Minimum Operating Temperature
- 40 C
Features
NO
Sensor Type
Inductive
Sensing Object
Metallic
Response Frequency
25Hz
Material - Body
Nickel-Plated Brass
Shielding
Shielded
Voltage - Supply
20 VAC ~ 264 VAC
Output Type
SCR-NO
Terminal Type
Connector
Package / Case
Cylinder, Threaded - M18
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
E2EX5Y1M4Q
J MUTUAL INTERFERENCE
When installing two or more Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are main-
tained.
Note: The figures in parentheses refer to Sensors operating at different frequencies.
J INSTALLATION
Power Reset Time
The Proximity Sensor is ready to operate within 100 ms after power
is supplied. If power supplies are connected to the Proximity Sensor
and load respectively, be sure to supply power to the Proximity Sen-
sor before supplying power to the load.
Power OFF
The Proximity Sensor may output a pulse signal when it is turned off.
Therefore, it is recommended to turn off the load before turning off
the Proximity Sensor.
Power Supply Transformer
When using a DC power supply, make sure that the DC power sup-
ply has an insulated transformer. Do not use a DC power supply with
an auto-transformer.
Sensing Target
Metal Coating:
The sensing distances of the Proximity Sensor vary with the metal
coating on sensing targets.
J WIRING
High-tension Lines
Wiring through Metal Conduit
If there is a power or high-tension line near the cord of the Proximity
Sensor, wire the cord through an independent metal conduit to pre-
vent against Proximity Sensor damage or malfunctioning.
Type
E2E-XjYj
AC 2-wire
E2E 2-WIRE AC
j j
A
Shielded
Unshielded
B
Dimension
A
B
A
B
M8
20 mm
15 mm
80 mm
60 mm
15
Cable Tractive Force
Do not pull cable with the tractive forces exceeding the following.
J MOUNTING
The Proximity Sensor must not be subjected to excessive shock
with a hammer when it is installed, or the Proximity Sensor may be
damaged or lose its water-resistance.
J ENVIRONMENT
Water Resistance
Do not use the Proximity Sensor underwater, outdoors, or in the
rain.
Operating Environment
Be sure to use the Proximity Sensor within its operating ambient
temperature range and do not use the Proximity Sensor outdoors to
maintain its reliability and life expectancy. Although the Proximity
Sensor is water resistant, a cover to protect the Proximity Sensor
from water or water soluble machining oil is recommended so that
its reliability and life expectancy can be maintained.
Do not use the Proximity Sensor in an environment with chemical
gas (e.g., strong alkaline or acid gasses including nitric, chromic,
and concentrated sulfuric acid gases).
Diameter
4 mm dia. max.
4 mm dia. min.
M12
30 (20) mm
20 (12) mm
120 (60) mm
100 (50) mm
M18
50 (30) mm
35 (18) mm
200 (100) mm
110 (60) mm
Tractive force
30 N max.
50 N max.
E2E 2-WIRE AC
M30
100 (50) mm
70 (35) mm
300 (100) mm
200 (100) mm