MAX1099CEAE Maxim Integrated Products, MAX1099CEAE Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX1099CEAE
Manufacturer Part Number
MAX1099CEAE
Description
Board Mount Temperature Sensors
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1099CEAE.pdf
(20 pages)
Specifications of MAX1099CEAE
Full Temp Accuracy
+/- 4 C
Package / Case
SSOP-16
Digital Output - Bus Interface
Serial (3-Wire)
Digital Output - Number Of Bits
10 bit
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Output Type
Digital
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX1099CEAE
Manufacturer:
MAXIM
Quantity:
16
Part Number:
MAX1099CEAE
Manufacturer:
MAXIM/美信
Quantity:
20 000
ence reflects the power requirement of an internal refer-
ence buffer amplifier that can accommodate external
loads. Temperature conversions at 100% duty cycle
increase supply currents to 440µA (400µA) through
additional amplification, buffer, and bias circuitry that is
otherwise inactive.
Place the MAX1098/MAX1099 in a low-current power-
down state between conversions to conserve power.
Select standby, standby plus, or shutdown through bits
PM1 and PM0 of the initialization byte (Table 3).
The MAX1098/MAX1099 assume the shutdown power
mode when V
Standby mode turns off the MAX1098/MAX1099 ADC,
internal clock, and reference buffer amplifier. Special
circuitry for temperature conversions is also deactivat-
ed. Wake-up time is limited by the reference buffer
amplifier and the associated bypass capacitor (see
Internal Reference). When an external reference is
used, wake-up time is 0.1ms.
Standby-plus mode is similar to the standby mode, but
the internal reference output buffer remains active to
shorten the wake-up time to 0.1ms for internal refer-
ence mode. When using an external reference, stand-
by-plus mode is equivalent to standby mode.
Shutdown mode turns off all functions other than start-
up circuitry, thereby reducing typical supply current to
2µA. Data registers are cleared. Use this power mode
when interconversion times are no less than 5ms.
This mode of operation samples and converts the sup-
ply voltage, V
reference voltage must be larger than V
operation to work properly. From the result of a conver-
sion (CODE), CODE = 64 V
The MAX1098/MAX1099 perform temperature measure-
ments with internal or external diode-connected transis-
tors through a three-step process. First, the diode bias
current changes from 31.6µA to 10µA to produce a
temperature-dependent bias voltage difference, which
is amplified by a factor of 20 and converted to digital
format. Second, the bias current changes from 31.6µA
to 100µA, and the bias voltage difference is similarly
amplified by a factor of 20 and converted to digital for-
mat. Third, the intermediate results are subtracted to
10-Bit Serial-Output Temperature Sensors
with 5-Channel ADC
16
______________________________________________________________________________________
DD
DD
is first applied.
/4, which is internally generated. The
Temperature Measurements
DD
/ V
REF
Standby-Plus Mode
Monitoring V
.
Shutdown Mode
Standby Mode
DD
/8 for the
DD
achieve a digital output that is proportional to absolute
temperature in degrees Kelvin.
The reference voltage used in conjunction with tempera-
ture measurements is derived from the internal reference
source to ensure that 1LSB corresponds to 1/8 of a
degree. To convert to degrees Celsius, subtract 273.15
from the temperature inferred from the ADC output.
Temperature measurements require a conversion time
of 2.2ms.
The MAX1098/MAX1099 provide a shield output buffer
voltage at SHO that is approximately 0.6V (one diode
drop) above V
measurements with an external diode, use this voltage
to suppress error-producing leakage currents (see
Remote Diode Shielding). Figure 7 shows the SHO out-
put circuit.
Temperature accuracy depends on having a good-
quality, diode-connected, small-signal transistor.
Accuracy has been experimentally verified for 2N3904
devices. CPUs and other ICs having on-board temper-
ature-sensing diodes can also be monitored if the
diode connections are floating.
Figure 7. SHO Output Circuit
Table 3. Power-Mode Selection
See Power Requirements in Electrical Characteristics.
PM1
0
0
1
1
PM0
0
1
0
1
Applications Information
DD
V
DD
2
Shutdown
Standby plus
Standby
Normal operation
/2. When performing temperature
Remote Diode Selection
Shield Output Buffer
5 µA
MODE
SHO