EMC1402-4-ACZL SMSC, EMC1402-4-ACZL Datasheet - Page 30
![no-image](/images/manufacturer_photos/0/6/617/smsc_sml.jpg)
EMC1402-4-ACZL
Manufacturer Part Number
EMC1402-4-ACZL
Description
Board Mount Temperature Sensors Dual Temp Snsr
Manufacturer
SMSC
Datasheet
1.EMC1402-1-ACZL-TR.pdf
(40 pages)
Specifications of EMC1402-4-ACZL
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Revision 1.36 (07-02-09)
6.11
ADDR.
22h
R/W
R/W
Bit 0 - INTMASK - Masks the ALERT pin from asserting when the Internal Diode temperature is out
of limit.
The Consecutive ALERT Register determines how many times an out-of-limit error or diode fault must
be detected in consecutive measurements before the ALERT or THERM pin is asserted. Additionally,
the Consecutive ALERT Register controls the SMBus Timeout functionality.
An out-of-limit condition (i.e. HIGH, LOW, or FAULT) occurring on the same temperature channel in
consecutive measurements will increment the consecutive alert counter. The counters will also be reset
if no out-of-limit condition or diode fault condition occurs in a consecutive reading.
When the ALERT pin is configured as an interrupt, when the consecutive alert counter reaches its
programmed value, the following will occur: the STATUS bit(s) for that channel and the last error
condition(s) (i.e. EHIGH) will be set to ‘1’, the ALERT pin will be asserted, the consecutive alert counter
will be cleared, and measurements will continue.
When the ALERT pin is configured as a comparator, the consecutive alert counter will ignore diode
fault and low limit errors and only increment if the measured temperature exceeds the High Limit.
Additionally, once the consecutive alert counter reaches the programmed limit, the ALERT pin will be
asserted, but the counter will not be reset. It will remain set until the temperature drops below the High
Limit minus the THERM Hysteresis value.
For example, if the CALRT[2:0] bits are set for 4 consecutive alerts, the high limits are set at 70°C,
and none of the channels are masked, then the ALERT pin will be asserted after the following four
measurements:
1. Internal Diode reads 71°C and the external diode reads 69°C. Consecutive alert counter for INT is
2. Both the Internal Diode and the External Diode read 71°C. Consecutive alert counter for INT is
3. The External Diode reads 71°C and the Internal Diode reads 69°C. Consecutive alert counter for
4. The Internal Diode reads 71°C and the external diode reads 71°C. Consecutive alert counter for
5. The Internal Diode reads 71°C and the external diode reads 71°C. Consecutive alert counter for
Bit 7 - TIMEOUT - Determines whether the SMBus Timeout function is enabled.
Consecutive ALERT Register
‘1’ - The External Diode channel will not cause the ALERT pin to be asserted if it is out of limit or
reports a diode fault.
‘0’ (default) - The Internal Diode channel will cause the ALERT pin to be asserted if it is out of limit.
‘1’ - The Internal Diode channel will not cause the ALERT pin to be asserted if it is out of limit.
‘0’ (default) - The SMBus Timeout feature is disabled. The SMCLK line can be held low indefinitely
without the device resetting its SMBus protocol.
‘1’ - The SMBus Timeout feature is enabled. If the SMCLK line is held low for more than 30ms,
then the device will reset the SMBus protocol.
incremented to 1.
incremented to 2and for EXT is set to 1.
INT is cleared and EXT is incremented to 2.
INT is set to 1 and EXT is incremented to 3.
INT is incremented to 2 and EXT is incremented to 4. The appropriate status bits are set for EXT
and the ALERT pin is asserted. EXT counter is reset to 0 and all other counters hold the last value
until the next temperature measurement.
Consecutive
REGISTER
ALERT
Table 6.12 Consecutive ALERT Register
TIME
OUT
B7
B6
DATASHEET
CTHRM[2:0]
B5
30
B4
B3
1°C Temperature Sensor with Beta Compensation
CALRT[2:0]
B2
B1
B0
-
SMSC EMC1402
DEFAULT
Datasheet
70h