LM4545VH National Semiconductor, LM4545VH Datasheet - Page 9

• Manufacturer Part Number: LM4545VH
• Description: IC AUDIO CODEC '97 18BIT 48LQFP
• Manufacturer: National Semiconductor
• Type: Audio Codec '97r

Specifications of LM4545VH

• Data Interface: Serial
• Resolution (bits): 18 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 90 / 89
• Voltage - Supply, Analog: 4.2 V ~ 5.5 V
• Voltage - Supply, Digital: 3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *LM4545VH

Pin Descriptions
Analog I/O
SDATA_OUT
HP_OUT_R
SDATA_IN
VREFOUT
XTL_OUT
Digital I/O and Clocking
Power Supplies and References
3DP,3DN
BIT_CLK
RESET#
XTL_IN
AFILT1
AFILT2
Name
Name
SYNC
Name
AVDD
DVDD
DVSS
AVSS
VREF
25,38
26,42
31,32
Pin
Pin
Pin
1,9
4,8
(Continued)
41
10
11
27
28
29
30
2
3
5
6
8
(Continued)
I / O
I / O
I / O
O
O
O
O
O
O
O
O
O
I
I
I
I
I
I
I
I
Functional Description
This is a post-mixed output for the right audio channel. The level of this output can be
adjusted from 0dB to −45dB in 1.5dB steps as well as muted via register 04h. HP_OUT_R
has a nominal gain of 9dB with respect to the right output mixer level and is designed for
driving a 32
24.576 MHz crystal input. Use a fundamental-mode type crystal. When operating from a
crystal, a 1M
24.576 MHz crystal output. When operating from a crystal, a 1M
connected across pins 2 and 3.
This data stream contains both control data and DAC audio data. This input is sampled by
the LM4545 on the falling edge of BIT_CLK.
12.288 MHz clock which is derived (divide by two) from the 24.576MHz crystal input
(XTL_IN).
This data stream contains both control data and ADC audio data. This output is clocked out
by the LM4545 on the rising edge of BIT_CLK.
48kHz sync pulse which signifies the beginning of both the SDATA_IN and SDATA_OUT
serial streams. SYNC must be synchronous to BIT_CLK.
This active low signal causes a hardware reset which returns the control registers to their
default conditions.
Analog supply pins.
Analog ground pins.
Digital supply pins.
Digital ground pins.
Nominal 2.2V reference output. Not intended to sink or source current. Bypassing of this pin
should be done with short traces to maximize performance.
Nominal 2.2V reference output. Can source up to 5mA of current and can be used to bias a
microphone. Do not connect any external capacitance to this pin.
This pin is not used and should be left open (NC). However, a capacitor to ground on this
pin is permitted as it will not affect performance.
This pin is not used and should be left open (NC). However, a capacitor to ground on this
pin is permitted as it will not affect performance.
These pins are used to complete the National 3D Sound circuit. Connect a 0.022µF
capacitor between pins 3DP and 3DN. The National 3D Sound can be turned on and off via
control register 20h. This is a fixed-depth type stereo enhance circuit, thus writing to register
22h has no effect. If National 3D Sound is not desired, then these pins should be left as no
connect (NC).
impedance with minimal distortion.
resistor must be connected across pins 2 and 3.
9
Functional Description
Functional Description
resistor must be
www.national.com