KSZ8842-16MQL Micrel Inc, KSZ8842-16MQL Datasheet - Page 49
![IC SWITCH 10/100 16BIT 128PQFP](/photos/6/81/68152/576-128-pqfp_sml.jpg)
KSZ8842-16MQL
Manufacturer Part Number
KSZ8842-16MQL
Description
IC SWITCH 10/100 16BIT 128PQFP
Manufacturer
Micrel Inc
Datasheets
1.KSZ8841-PMQLI.pdf
(2 pages)
2.KSZ8842-16MQL.pdf
(126 pages)
3.KSZ8842-16MQL.pdf
(141 pages)
Specifications of KSZ8842-16MQL
Data Rate
100Mbps
Controller Type
Ethernet Switch Controller
Interface
PCI
Voltage - Supply
3.1 V ~ 3.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
128-MQFP, 128-PQFP
No. Of Ports
1
Ethernet Type
IEEE 802.3u
Supply Current
122mA
Supply Voltage Range
3.1V To 3.5V
Operating Temperature Range
0°C To +70°C
Digital Ic Case Style
QFP
No. Of
RoHS Compliant
Number Of Primary Switch Ports
2
Internal Memory Buffer Size
32
Operating Supply Voltage (typ)
3.3V
Fiber Support
Yes
Integrated Led Drivers
Yes
Phy/transceiver Interface
MII
Power Supply Type
Analog/Digital
Package Type
PQFP
Data Rate (typ)
10/100Mbps
Vlan Support
Yes
Operating Temperature (max)
70C
Operating Temperature (min)
0C
Pin Count
128
Mounting
Surface Mount
Jtag Support
No
Operating Supply Voltage (max)
3.5V
Operating Supply Voltage (min)
3.1V
Operating Temperature Classification
Commercial
Interface Type
PCI
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
576-1634 - BOARD EVALUATION KSZ8842-16MQL
Current - Supply
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
576-1478-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
KSZ8842-16MQLI
Manufacturer:
MICREL
Quantity:
760
The format for ConfigParam is shown in Table 13.
Loopback Support
The KSZ8842M provides loopback support for remote diagnostic of failure. In loopback mode, the speed at both PHY
ports will be set to 100BASE-TX full-duplex mode. Two types of loopback are supported: Far-end Loopback and Near-end
(Remote) Loopback.
Far-end Loopback
Far-end loopback is conducted between the KSZ8842M’s two PHY ports. The loopback path starts at the “Originating.”
PHY port’s receive inputs (RXP/RXM), wraps around at the “loopback” PHY port’s PMD/PMA, and ends at the
“Originating” PHY port’s transmit outputs (TXP/TXM).
Bit [8] of registers P1CR4 and P2CR4 is used to enable far-end loopback for ports 1 and 2, respectively. Alternatively, Bit
[14] of registers P1MBCR and P2MBCR can also be used to enable far-end loopback. The port 2 far-end loopback path is
illustrated in the Figure 15.
Near-end (Remote) Loopback
Near-end (Remote) loopback is conducted at either PHY port 1 or PHY port 2 of the KSZ8842M. The loopback path starts
at the PHY port’s receive inputs (RXPx/RXMx), wraps around at the same PHY port’s PMD/PMA, and ends at the PHY
port’s transmit outputs (TXPx/TXMx).
Bit [1] of registers P1PHYCTRL and P2PHYCTRL is used to enable near-end loopback for ports 1 and 2, respectively.
Alternatively, Bit [9] of registers P1SCSLMD and P2SCSLMD can also be used to enable near-end loopback. The both
ports 1 and 2 near-end loopback paths are illustrated in the following Figure 16.
Micrel, Inc.
October 2007
Bit
15 -2
1
0
Bit Name
Reserved
Clock_Rate
ASYN_8bit
Description
Reserved
Internal clock rate selection
0: 125 MHz
1: 25 MHz
Note: At power up, this chip operates on 125 MHz clock. The internal frequency can be
dropped to 25 MHz via the external EEPROM.
Async 8-bit or 16-bit bus select
1= bus is configured for 16-bit width
0= bus is configured for 8-bit width
(32-bit width, KSZ8842-32, don’t care this bit setting)
Table 13. ConfigParam Word in EEPROM Format
49
KSZ8842-16/32 MQL/MVL/MVLI/MBL
M9999-102207-1.9