CY7C65640A-LTXC Cypress Semiconductor Corp, CY7C65640A-LTXC Datasheet - Page 6

• Manufacturer Part Number: CY7C65640A-LTXC
• Description: IC USB HUB CTLR HS 56VQFN
• Manufacturer: Cypress Semiconductor Corp
• Series: TetraHub™r
• Type: USB Interface ICr

Specifications of CY7C65640A-LTXC

• Package / Case: 56-VQFN Exposed Pad, 56-HVQFN, 56-SQFN, 56-DHVQFN
• Controller Type: USB Hub
• Interface: SPI Serial
• Voltage - Supply: 3.15 V ~ 3.45 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Current - Supply: 260mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Number Of Bits: 9
• Operating Temperature Range: 0 C to + 70 C
• Propagation Delay Time Ns: 50 ns
• Resistance: 45 Ohms
• Supply Current: 460 mA
• Operating Supply Voltage: 3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: CY4602 - KIT USB 4-PORT HUB REF DESIGN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-2931

Table 0-1. CY7C65640APin Assignments
Document #: 38-08019 Rev. *J
SPI INTERFACE
UPSTREAM PORT
Pin
11
15
19
23
27
33
39
45
55
12
16
20
24
28
34
40
47
50
56
21
22
46
26
25
48
49
17
18
3
7
4
8
BUSPOWER
SPI_SCK
RESET#
SPI_CS
SPI_SD
XOUT
Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
XIN
D–
D+
Output
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Type
Input
Input
Input
I/O/Z
I/O/Z
I/O/Z
O
O
Default
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
O
O
Z
Z
Z
Description
V
V
V
V
V
V
V
V
V
V
V
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
GND. Connect to Ground with as short a path as possible.
24-MHz Crystal IN or External Clock Input.
24-MHz Crystal OUT.
Active LOW Reset. This pin resets the entire chip. It is normally tied to V
through a 100K resistor, and to GND through a 0.1-µF capacitor. Other than this,
no other special power-up procedure is required.
VBUS. Connect to the VBUS pin of the upstream connector. This signal indicates
to the hub that it is in a powered state, and may enable the D+ pull-up resistor
to indicate a connection. (The hub will do so after the external EEPROM is read,
unless it is put into a high speedhigh speedhigh speed mode by the upstream
hub). The hub can not be bus powered, and the VBUS signal must not be used
as a power source.
SPI Chip Select. Connect to CS pin of the EEPROM.
SPI Clock. Connect to EEPROM SCK pin.
SPI Dataline Connect to GND with 15-KΩ resistor and to the Data I/O pins of
the EEPROM.
Upstream D– Signal.
Upstream D+ Signal.
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
. This signal provides power to the chip.
CY7C65640A
Page 6 of 23
CC
[+] Feedback