PKJ4113PIT Ericsson Power Modules, PKJ4113PIT Datasheet - Page 34
![no-image](/images/manufacturer_photos/0/2/233/ericsson_power_modules_sml.jpg)
PKJ4113PIT
Manufacturer Part Number
PKJ4113PIT
Description
DC/DC Converters & Regulators 12 Vdc 8.3A Iso Input 36-75V 100W
Manufacturer
Ericsson Power Modules
Series
PKJr
Datasheet
1.PKJ4113PIT.pdf
(39 pages)
Specifications of PKJ4113PIT
Product
Isolated
Output Power
100 W
Input Voltage Range
36 V to 75 V
Number Of Outputs
1
Output Voltage (channel 1)
12 V
Output Current (channel 1)
8.3 A
Isolation Voltage
1.5 KV
Package / Case Size
Half Brick
Output Type
Isolated
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PKJ4113PIT
Manufacturer:
ERICSSON
Quantity:
37
Company:
Part Number:
PKJ4113PIT
Manufacturer:
ERICSSON
Quantity:
530
Part Number:
PKJ4113PIT
Manufacturer:
ERICSSON/爱立信
Quantity:
20 000
Operating information, cont.
Input And Output Impedance
The impedance of both the input source and the load will
interact with the impedance of the DC/DC converter. It is
important that the input source has low characteristic
impedance. The converters are designed for stable operation
without external capacitors connected to the input or output.
The performance in some applications can be enhanced by
addition of external capacitance as described under External
Decoupling Capacitors. If the input voltage source contains
significant inductance, the addition of a 100 µF capacitor
across the input of the converter will ensure stable operation.
The capacitor is not required when powering the DC/DC
converter from an input source with an inductance below
10 µH.
External Decoupling Capacitors
When powering loads with significant dynamic current
requirements, the voltage regulation at the point of load can
be improved by addition of decoupling capacitors at the load.
The most effective technique is to locate low ESR ceramic
and electrolytic capacitors as close to the load as possible,
using several parallel capacitors to lower the effective ESR.
The ceramic capacitors will handle high-frequency dynamic
load changes while the electrolytic capacitors are used to
handle low frequency dynamic load changes. Ceramic
capacitors will also reduce any high frequency noise at the
load.
It is equally important to use low resistance and low
inductance PCB layouts and cabling.
External decoupling capacitors will become part of the control
loop of the DC/DC converter and may affect the stability
margins. As a “rule of thumb”, 100 µF/A of output current can
be added without any additional analysis.
The recommended absolute maximum value of output
capacitance is 10 000 µF. For further information please
contact your local Ericsson Power Modules representative.
Prepared (also subject responsible if other)
SEC/D EPHILIP
Approved
SEC/D EPHILIP
PKJ 4000 PI series
DC/DC converters, Input 36-75 V, Output 30A/150W
Checked
(MICJOHN)
Parallel Operation
Two converters may be paralleled for redundancy if the total
power is equal or less than P
parallel the converters without using external current sharing
circuits.
Over Temperature Protection (OTP)
The converters are protected from thermal overload by an
internal over temperature shutdown circuit. When the
baseplate or case temperature exceeds 110°C the converter
will shut down immediately (latching). The converter can be
restarted by cycling the input voltage or using the remote
control function.
Over Voltage Protection (OVP)
The converters have output over voltage protection that will
shut down the converter in over voltage conditions. The
converter can be restarted by cycling the input voltage or
using the remote control function.
Over Current Protection (OCP)
The converters include current limiting circuitry for protection
at continuous overload.
The output voltage will decrease towards zero for output
currents in excess of max output current (max I
converter will resume normal operation after removal of the
overload. The load distribution should be designed for the
maximum output short circuit current specified.
PRODUCT SPECIFICATION
No.
3/1301-BMR630
Date
2006-1-27
Technical Specifi cation
EN/LZT 146 309 R1B February 2006
© Ericsson Power Modules AB
Rev
A
O
max. It is not recommended to
Reference
O
). The
4 (6)
34